Repara tus cosas Comunidad Tienda

Etekcity Lasergrip 1080 Motherboard Replacement

Introducción

This guide will show how to remove everything from the motherboard and have it by itself for replacement. This guide should only be necessary if nothing else works. It is a last resort as the motherboard is the least likely to malfunction. The tools needed are a screwdriver and soldering iron. The soldering iron will become very hot, so that is a potential hazard. For those who are not comfortable soldering, there is a link to a soldering guide in the Troubleshooting section of the device page.

Qué necesitas

  1. Etekcity Lasergrip 1080 Motherboard Replacement, Battery: paso 1, imagen 1 de 1

    • Pull the battery cover away from the handle by gripping near the thumb groove.

    Editar

  2. Etekcity Lasergrip 1080 Motherboard Replacement: paso 2, imagen 1 de 1

    • Gently pull the battery out of the handle.

    • Excessive force could damage wires.

    Editar

  3. Etekcity Lasergrip 1080 Motherboard Replacement: paso 3, imagen 1 de 2 Etekcity Lasergrip 1080 Motherboard Replacement: paso 3, imagen 2 de 2

    • Disconnect the battery by pulling the connector away from it.

    • Positive first

    • Negative second

    • When replacing the battery, this order is reversed.

    Editar

  4. Etekcity Lasergrip 1080 Motherboard Replacement, Buttons: paso 4, imagen 1 de 2 Etekcity Lasergrip 1080 Motherboard Replacement, Buttons: paso 4, imagen 2 de 2

    • Remove the battery cover from the device by pulling it straight out.

    Editar

  5. Etekcity Lasergrip 1080 Motherboard Replacement: paso 5, imagen 1 de 2 Etekcity Lasergrip 1080 Motherboard Replacement: paso 5, imagen 2 de 2

    • Using the plastic opening tool remove the front and rear yellow covers.

    • When removing the back cover, be careful not to lose the buttons as they are not connected.

    Editar

  6. Etekcity Lasergrip 1080 Motherboard Replacement: paso 6, imagen 1 de 1

    • Remove the two 3.1 mm Phillips #0 screws.

    Editar

  8. Etekcity Lasergrip 1080 Motherboard Replacement: paso 7, imagen 1 de 2 Etekcity Lasergrip 1080 Motherboard Replacement: paso 7, imagen 2 de 2

    • Pull the two halves apart.

    • Be careful not to lose any components on the inside.

    Editar

  9. Etekcity Lasergrip 1080 Motherboard Replacement: paso 8, imagen 1 de 1

    • Realign the buttons with the button terminals.

    • Red terminal to red button.

    • Orange terminal to orange button.

    • Yellow terminal to yellow button.

    Editar

  10. Etekcity Lasergrip 1080 Motherboard Replacement, Etekcity Lasergrip 1080 Trigger Replacement: paso 9, imagen 1 de 2 Etekcity Lasergrip 1080 Motherboard Replacement, Etekcity Lasergrip 1080 Trigger Replacement: paso 9, imagen 2 de 2

    • Carefully pull the trigger out.

    • The trigger is spring loaded, so be careful that you do not lose the spring as you pull the trigger out.

    • To put the trigger back in, align the peg with the hole in the handle and align the shaft with the button terminal.

    Editar

  11. Etekcity Lasergrip 1080 Motherboard Replacement, Laser: paso 10, imagen 1 de 1

    • Pull the motherboard out of its slot in the device.

    Editar

  12. Etekcity Lasergrip 1080 Motherboard Replacement: paso 11, imagen 1 de 1

    • Use a soldering iron to melt the solder that holds the wires for the laser to the motherboard.

    • Soldering irons are hot and should only be handled by those who know what they are doing and are wearing proper safety equipment. There is a link to a soldering guide in the Troubleshooting section of the device page.

    Editar

  13. Etekcity Lasergrip 1080 Motherboard Replacement, Sensor: paso 12, imagen 1 de 1

    • Pull the motherboard out of its slot in the device.

    Editar

  14. Etekcity Lasergrip 1080 Motherboard Replacement: paso 13, imagen 1 de 1

    • Using a soldering iron, melt the solder that holds the wires for the sensor to the motherboard.

    • Soldering irons are hot and should only be handled by those who know what they are doing and are wearing proper safety equipment. There is a link to a soldering guide in the Troubleshooting section of the device page.

    Editar

  15. Etekcity Lasergrip 1080 Motherboard Replacement, Battery Connector: paso 14, imagen 1 de 1

    • Pull the motherboard out of its slot in the device.

    Editar

  16. Etekcity Lasergrip 1080 Motherboard Replacement: paso 15, imagen 1 de 1

    • Use a soldering iron and melt the solder where the battery connector's wires are attached to the motherboard.

    • Soldering irons are hot and should only be handled by those who know what they are doing and are wearing proper safety equipment. There is a link to a soldering guide in the Troubleshooting section of the device page.

    Editar

  17. Etekcity Lasergrip 1080 Motherboard Replacement, Screen: paso 16, imagen 1 de 1

    • Carefully pull the motherboard out of its slot in the body of the device.

    Editar

  18. Etekcity Lasergrip 1080 Motherboard Replacement: paso 17, imagen 1 de 2 Etekcity Lasergrip 1080 Motherboard Replacement: paso 17, imagen 2 de 2

    • Unscrew the two 3.4 mm screws on the motherboard.

    Editar

  19. Etekcity Lasergrip 1080 Motherboard Replacement: paso 18, imagen 1 de 1

    • Take off the cover and separate the parts.

    • All of these parts are fragile and mishandling them may cause damage.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 1 otro colaborador

Patrick Crawford

Miembro Desde 08/26/15

741 Reputación

6 Guías creadas

Insignias: 15

+ 12 más insignias

Equipo

USF Tampa, Team 5-1, Blackwell Fall 2015 Miembro de USF Tampa, Team 5-1, Blackwell Fall 2015

USFT-BLACKWELL-F15S5G1

3 Miembros

9 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 5

Ultimos 30 días: 12

Todo El Tiempo: 435