Repara tus cosas Comunidad Tienda

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

Encoder Strip Replacement

Introducción

Replace the encoder strip.

Qué necesitas

  1. Encoder Strip Replacement, Remove Back Panel: paso 1, imagen 1 de 1

    • Remove the back panel by inserting your fingers into the indentations next to the tabs. Press the tabs inward towards each other while pulling the back panel toward you.

    Traducir

  2. Encoder Strip Replacement, Remove Inner Back Pannel: paso 2, imagen 1 de 2 Encoder Strip Replacement, Remove Inner Back Pannel: paso 2, imagen 2 de 2

    • Using the T10 Torx Security Bit Screwdriver, unscrew the screws on the upper left and right corners of the inner panel to remove the inner back panel.

    Traducir

  3. Encoder Strip Replacement, Remove Upper Portion: paso 3, imagen 1 de 2 Encoder Strip Replacement, Remove Upper Portion: paso 3, imagen 2 de 2

    • Press down on the two plastic hinges to remove the upper portion of printer.

    Traducir

  4. Encoder Strip Replacement, Unplug Speaker Wire: paso 4, imagen 1 de 1

    • Grasp the plastic plug on the end of the speaker wire, then gently pull the plug away from the printer until the wire is removed.

    Traducir

  6. Encoder Strip Replacement, Removing Scanner Tray: paso 5, imagen 1 de 2 Encoder Strip Replacement, Removing Scanner Tray: paso 5, imagen 2 de 2

    • Rotate the printer so the paper tray is facing towards you.

    • Gently lift the scanner tray up and away from the printer.

    • Press the gray plastic tabs inward to release the tabs from the printer.

    Traducir

  7. Encoder Strip Replacement, Removing Scanner Tray - cont.: paso 6, imagen 1 de 1

    • Returning to the back of the printer, remove the scanner from the back hinges.

    • With pressure applied, the scanner will detach easily.

    Traducir

  8. Encoder Strip Replacement: paso 7, imagen 1 de 1

    • Gently grasp and unplug the two white ribbon cables from the printer body.

    • Be sure to grasp the cable at the connector and not to pull on the wires themselves.

    Traducir

  9. Encoder Strip Replacement: paso 8, imagen 1 de 1

    • Unplug the white plastic multi-wire connector (with orange, black, red, and brown wires) from it's port.

    • Be sure to grasp the white connector and not to pull on the wires themselves.

    Traducir

  10. Encoder Strip Replacement, Detaching the Scanner Tray: paso 9, imagen 1 de 1

    • Detach the scanner tray from the printer by lifting the scanner tray off the printer body.

    Traducir

  11. Encoder Strip Replacement, Encoder Strip: paso 10, imagen 1 de 2 Encoder Strip Replacement, Encoder Strip: paso 10, imagen 2 de 2

    • Locate the panel labeled with a HP support link sticker.

    • Release the tab by the support link sticker.

    • Remove the black screw below the tab.

    Traducir

  12. Encoder Strip Replacement: paso 11, imagen 1 de 1

    • Remove the two black screws closest to the printer tray.

    Traducir

  13. Encoder Strip Replacement: paso 12, imagen 1 de 1

    • Unhook the encoder strip from its small silver hooks and remove it from the printer.

    • To replace, feed the new encoder strip through the silver hooks.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

4 personas más completaron esta guía.

Autor

con 8 otros colaboradores

Jeremy Mahrt

Miembro Desde 05/08/11

286 Reputación

2 Guías creadas

Insignias: 11

+ 8 más insignias

Equipo

Cal Poly, Team 12-31, Maness Spring 2011 Miembro de Cal Poly, Team 12-31, Maness Spring 2011

CPSU-MANESS-S11S12G31

5 Miembros

9 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 4

Ultimos 30 días: 13

Todo El Tiempo: 29,358