Saltar al contenido principal

DualShock 4 Touch Pad Replacement

Qué necesitas

  1. DualShock 4 Touch Pad Replacement, Controller: paso 1, imagen 1 de 1
    • Using the Phillips #00 Screwdriver, remove the four 6.0 mm screws securing the rear cover to the controller.

    • Be careful loosening the screws, using the wrong sized screwdriver, or letting the screwdriver slip can permanently damage the screw heads, making removal extremely difficult.

  2. DualShock 4 Touch Pad Replacement: paso 2, imagen 1 de 3 DualShock 4 Touch Pad Replacement: paso 2, imagen 2 de 3 DualShock 4 Touch Pad Replacement: paso 2, imagen 3 de 3
    • Four fragile plastic clips hold the casing together. You can see their locations more clearly in this guide.

    • The clips help hold the seams together. If you break these clips, the controller will still work.

    • Beginning with the left handle:

    • Pinch the left handle of the controller to introduce an opening.

    • Wedge a plastic opening tool into the opening and slide it up towards the joystick.

    • Pull down on tool to pry open the casing.

    • Repeat these steps for the right handle.

  3. DualShock 4 Touch Pad Replacement: paso 3, imagen 1 de 3 DualShock 4 Touch Pad Replacement: paso 3, imagen 2 de 3 DualShock 4 Touch Pad Replacement: paso 3, imagen 3 de 3
    • Wedge a plastic opening tool into the case-splittings and pull down to crack open the casing near the following buttons:

    • Share button

    • Options button

    • Split the plastic covers of the controller apart, taking note that they will still be attached by circuit board ribbons.

    • Three small pieces are often released from the framework. To prevent loss, maintain a controlled work field.

    • 2 Trigger Springs

    • 1 Grey Reset Button Extension

  4. DualShock 4 Touch Pad Replacement, Disconnect the battery: paso 4, imagen 1 de 2 DualShock 4 Touch Pad Replacement, Disconnect the battery: paso 4, imagen 2 de 2
    • Use tweezers or your fingers to grab and disconnect the head of the battery cable from the motherboard.

    • Only pull on the head of the connector—don't pull on the cable itself.

  5. DualShock 4 Touch Pad Replacement, Remove the battery: paso 5, imagen 1 de 1
    • Remove the battery.

  6. DualShock 4 Touch Pad Replacement, Disassembling DualShock 4 Motherboard Assembly: paso 6, imagen 1 de 1
    • Remove the single 6.0 mm Phillips screw found below the battery retainer with the Phillips #00 Screwdriver.

    • Do not forcefully loosen the screw, as it may amount to permanent damage of the threads, making removal impossible.

  7. DualShock 4 Touch Pad Replacement: paso 7, imagen 1 de 2 DualShock 4 Touch Pad Replacement: paso 7, imagen 2 de 2
    • Gently detach the touchpad ribbon connected to the motherboard using the blunt forceps. The touchpad ribbon is connected to the motherboard by a connector that flips to tighten and loosen. During reassembly, to reattach the ribbon, the plastic tray will need to be gently removed from the motherboard and the flip-lock flipped up.

  8. DualShock 4 Touch Pad Replacement: paso 8, imagen 1 de 2 DualShock 4 Touch Pad Replacement: paso 8, imagen 2 de 2
    • Carefully dislodge the motherboard assembly from the front cover.

    • Vibration motors are loosely attached to the motherboard assembly. Provide support at the two ends to ease the separation.

    • When removing the motherboard assembly, try not to tilt the front cover upside down as the buttons and their covers may fall out.

  9. DualShock 4 Touch Pad Replacement, Disassembly Complete: paso 9, imagen 1 de 3 DualShock 4 Touch Pad Replacement, Disassembly Complete: paso 9, imagen 2 de 3 DualShock 4 Touch Pad Replacement, Disassembly Complete: paso 9, imagen 3 de 3
    • Successful disassembly of the controller will result in the following three parts, respectively:

    • Motherboard Assembly

    • Front Cover

    • Rear Cover

  10. DualShock 4 Touch Pad Replacement, Touch Pad: paso 10, imagen 1 de 1
    • After the motherboard is set aside, lay the front panel on the ground.

    • You can now see the touch pad which is outlined on the top and bottom by an orange line.

  11. DualShock 4 Touch Pad Replacement: paso 11, imagen 1 de 3 DualShock 4 Touch Pad Replacement: paso 11, imagen 2 de 3 DualShock 4 Touch Pad Replacement: paso 11, imagen 3 de 3
    • Now pick the front panel up, and use one hand to press the touch pad up from the front of the panel.

    • There are no other restrictions attached to the touch pad. It should slide right out and back in without any effort.

Conclusión

To reassemble your device, follow these instructions in reverse order.

26 personas más completaron esta guía.

Mark

Miembro Desde 01/21/14

7,710 Reputación

7 Guías creadas

Equipo

Cal Poly, Team 6-21, Maness Winter 2014 Miembro de Cal Poly, Team 6-21, Maness Winter 2014

CPSU-MANESS-W14S6G21

4 Miembros

41 Guías creadas

5 comentarios

when put back the right side and the bottom doesnt click properly. What am I doing wrong?

Karakan Dement - Contestar

You ever figure this out?

Ayushmaan Ganotra -

I disassembled my controller and changed the sticks and case now the controller moves on it's own and gets stuck when moving ... How can I fix this or is there something I may have done wrong when I was reassembling it???

tomgunnz45 - Contestar

So, there are some differences with the new DS4 from 2016. and frustratingly the flip up piece that is used to tighten the ribbon connection for the touch pad is no longer there. I have no idea how to get the ribbon back into it's connector. Any ideas?

Jacob L - Contestar

when i took the ribbon cable out, the cover when with it now i cant put the cover back so i can put back the cable

Brandon Butanda - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 9

Ultimos 7 días: 87

Ultimos 30 días: 444

Todo El Tiempo: 65,074