Repara tus cosas Comunidad Tienda

Dremel 4000 Power Cord Replacement

Introducción

In the following steps you will access the electrical assembly, and remove the positive and negative wires that connect the power cord to the assembly.

Qué necesitas

  1. Dremel 4000 Power Cord Replacement, Back Case: paso 1, imagen 1 de 2 Dremel 4000 Power Cord Replacement, Back Case: paso 1, imagen 2 de 2

    • Start by removing the housing cap by unscrewing it.

    • Next, unscrew the now exposed collet nut while holding down the shaft lock button.

    • To remove the collet nut, you may need to use the small open-end wrench provided with the Dremel.

    Editar

  2. Dremel 4000 Power Cord Replacement: paso 2, imagen 1 de 1

    • Using your hands, carefully remove hanger from casing.

    Editar

  3. Dremel 4000 Power Cord Replacement: paso 3, imagen 1 de 2 Dremel 4000 Power Cord Replacement: paso 3, imagen 2 de 2

    • Remove the brush caps (one on each side) by using a flathead screwdriver bit.

    • The brush caps are spring loaded.

    Editar

  4. Dremel 4000 Power Cord Replacement: paso 4, imagen 1 de 1

    • Using the Torx 15 screwdriver tip, remove the 5 screws (12.5 mm) that hold the casing together.

    Editar

  6. Dremel 4000 Power Cord Replacement: paso 5, imagen 1 de 1

    • Use a plastic opening tool to gently wedge apart the hard plastic threads.

    Editar

  7. Dremel 4000 Power Cord Replacement: paso 6, imagen 1 de 1

    • Use your hands to carefully remove the back casing so that none of the components fall out.

    Editar

  8. Dremel 4000 Power Cord Replacement, Power Cord: paso 7, imagen 1 de 2 Dremel 4000 Power Cord Replacement, Power Cord: paso 7, imagen 2 de 2

    • To clear access to the electrical assembly, remove the variable speed dial cap and blue power lever, and set them aside.

    Editar

  9. Dremel 4000 Power Cord Replacement: paso 8, imagen 1 de 1

    • Using your fingers, carefully pull the circuit board from the casing. This will make it easier to remove the power cord.

    Editar

  10. Dremel 4000 Power Cord Replacement: paso 9, imagen 1 de 1

    • Each wire is fed through a small opening on the circuit board and held with a flat head screw.

    • Loosen the screw just enough to remove the wire by gently pulling it with your hand.

    Editar

  11. Dremel 4000 Power Cord Replacement: paso 10, imagen 1 de 1

    • Carefully remove both wires from circuit board with your hands.

    • Take careful note of which side has the black wire and which has the white wire.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

5 personas más completaron esta guía.

Autor

con 2 otros colaboradores

John Cobb

Miembro Desde 01/20/16

1,689 Reputación

4 Guías creadas

Insignias: 21

+ 18 más insignias

Equipo

USF Tampa, Team 15-4, Remmell Spring 2016 Miembro de USF Tampa, Team 15-4, Remmell Spring 2016

USFT-REMMELL-S16S15G4

4 Miembros

13 Guías creadas

Un comentario

Super handy guide after my guide dog decided to chew through the cable!

Geoff Palmer - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 10

Ultimos 30 días: 35

Todo El Tiempo: 5,669