Repara tus cosas Comunidad Tienda

Disassembling the Circuit Board

Introducción

This guide provides the steps necessary to disconnect the circuit board from the bottom plastic housing. It also goes over how to remove the heat sink and base tube in order to get to the auxiliary jack and power jack.

Qué necesitas

  1. Disassembling the Circuit Board, Cracking the Case: paso 1, imagen 1 de 1

    • Turn the device upside down so that the three rubber pads are facing up.

    Traducir

  2. Disassembling the Circuit Board: paso 2, imagen 1 de 1

    • Use a heat gun (set to low) to apply heat to one of the rubber pads until you can easily remove the pad. This step takes around 5-7 minutes.

    Traducir

  3. Disassembling the Circuit Board: paso 3, imagen 1 de 1

    • Remove the heated rubber pad with a plastic opening tool.

    • Repeat steps 2 and 3 for the two remaining rubber pads.

    Traducir

  4. Disassembling the Circuit Board: paso 4, imagen 1 de 2 Disassembling the Circuit Board: paso 4, imagen 2 de 2

    • Remove the six 1cm T-10 torx screws on the bottom of the device (found under the rubber pads) using a T-10 Torx screwdriver.

    Traducir

  6. Disassembling the Circuit Board: paso 5, imagen 1 de 3 Disassembling the Circuit Board: paso 5, imagen 2 de 3 Disassembling the Circuit Board: paso 5, imagen 3 de 3

    • Open the device along its seam.

    • Be careful when separating the device because there are wires connecting the two seperate halves.

    Traducir

  7. Disassembling the Circuit Board: paso 6, imagen 1 de 1

    • Disconnect the ribbon cable connector from the top half of the device by pulling outward and parallel to the connecting pins.

    Traducir

  8. Disassembling the Circuit Board: paso 7, imagen 1 de 2 Disassembling the Circuit Board: paso 7, imagen 2 de 2

    • Locate and disconnect the two molex connectors found on either side of the ribbon cable connector on the bottom half of the device.

    Traducir

  9. Disassembling the Circuit Board, Circuit Board: paso 8, imagen 1 de 2 Disassembling the Circuit Board, Circuit Board: paso 8, imagen 2 de 2

    • Remove the three 1 cm T-10 Torx screws.

    Traducir

  10. Disassembling the Circuit Board: paso 9, imagen 1 de 1

    • Carefully press out the white base tube and push up on the circuit board.

    • Note that there is a small wire connecting the circuit board to the base.

    Traducir

  11. Disassembling the Circuit Board: paso 10, imagen 1 de 2 Disassembling the Circuit Board: paso 10, imagen 2 de 2

    • Pull the white wire out of the hot glue.

    Traducir

  12. Disassembling the Circuit Board: paso 11, imagen 1 de 3 Disassembling the Circuit Board: paso 11, imagen 2 de 3 Disassembling the Circuit Board: paso 11, imagen 3 de 3

    • Unbolt the heatsink with a 5.5-mm socket and a Phillips PH1 screwdriver.

    • Remove the heat sink; it should detach from the bottom of the device.

    Traducir

  13. Disassembling the Circuit Board: paso 12, imagen 1 de 3 Disassembling the Circuit Board: paso 12, imagen 2 de 3 Disassembling the Circuit Board: paso 12, imagen 3 de 3

    • Remove the T-10 torx screw on the bottom of the device that attaches the base tube to the circuit board.

    • Turn the device so that the base tube is on top.

    • Remove the base tube by pulling up.

    • May need to cut the rubber adhesive between the base tube to the circuit board.

    Traducir
Conclusión

To reassemble your device, follow these steps in reverse order.

2 personas más completaron esta guía.

Autor

con 4 otros colaboradores

Janessa D Cabrera

Miembro Desde 01/23/14

514 Reputación

4 Guías creadas

Insignias: 10

+ 7 más insignias

Equipo

Cal Poly, Team 9-28, Maness Winter 2014 Miembro de Cal Poly, Team 9-28, Maness Winter 2014

CPSU-MANESS-W14S9G28

4 Miembros

7 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 11

Ultimos 30 días: 23

Todo El Tiempo: 4,650