Repara tus cosas Comunidad Tienda

Disassembling the Canon PowerShot A200 Case

Introducción

These are instructions to disassemble the camera case so that internal components can be accessed.

This is a prerequisite guide for repairs to the Canon PowerShot A200.

Qué necesitas

  1. Disassembling the Canon PowerShot A200 Case, Canon PowerShot A200: paso 1, imagen 1 de 1

    • Use a Phillips #00 screwdriver to remove the two screws located at the bottom of the camera.

    Editar

  2. Disassembling the Canon PowerShot A200 Case: paso 2, imagen 1 de 2 Disassembling the Canon PowerShot A200 Case: paso 2, imagen 2 de 2

    • Locate the screw and the rubber covering on the left side of the camera. Slide the rubber covering to expose a second screw.

    • Remove the two screws with the Phillips #00 screwdriver.

    Editar

  3. Disassembling the Canon PowerShot A200 Case: paso 3, imagen 1 de 2 Disassembling the Canon PowerShot A200 Case: paso 3, imagen 2 de 2

    • Open the battery compartment on the right side of the camera by pushing slightly in the direction of the arrow.

    • Be sure to remove the memory card.

    • Remove the two screws by the memory card slot using the Phillips #00 screwdriver.

    Editar

  4. Disassembling the Canon PowerShot A200 Case: paso 4, imagen 1 de 2 Disassembling the Canon PowerShot A200 Case: paso 4, imagen 2 de 2

    • Pull the grey tab towards the back of the camera. Lift the black cover to expose the battery slots.

    • Remove the two visible screws with the Phillips #00 screwdriver.

    • During reassembly, the holes for these screws must align properly with the interior of the camera body. Then the black battery cover must lie flat and be held in place by the grey tab.

    Editar

  5. Disassembling the Canon PowerShot A200 Case: paso 5, imagen 1 de 2 Disassembling the Canon PowerShot A200 Case: paso 5, imagen 2 de 2

    • Remove the screen battery located to the left of the screen.

    • Set the screen battery aside for reassembly

    Editar

  6. Disassembling the Canon PowerShot A200 Case: paso 6, imagen 1 de 2 Disassembling the Canon PowerShot A200 Case: paso 6, imagen 2 de 2

    • Gently pull the camera apart from the top.

    • Be careful. The two halves are still attached by two short ribbons at the bottom of the camera.

    Editar

  7. Disassembling the Canon PowerShot A200 Case: paso 7, imagen 1 de 2 Disassembling the Canon PowerShot A200 Case: paso 7, imagen 2 de 2
    Herramienta utilizada en este paso:
    Tweezers
    $4.99
    Comprar

    • Locate the black tabs on either side of the white ribbon.

    • Use the metal tweezers to gently move these tabs to the outside edges of the ribbon.

    • Gently pull the white ribbon out from its connection.

    Editar

  8. Disassembling the Canon PowerShot A200 Case: paso 8, imagen 1 de 3 Disassembling the Canon PowerShot A200 Case: paso 8, imagen 2 de 3 Disassembling the Canon PowerShot A200 Case: paso 8, imagen 3 de 3

    • Locate the black tabs on either side of the orange ribbon.

    • Use the metal tweezers to gently move these tabs to the outside edges of the ribbon.

    • Gently pull the orange ribbon out of its connection.

    • Your camera will now be in two separate pieces.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 17 otros colaboradores

Daniel Stone

Miembro Desde 01/28/11

101 Reputación

1 Guía escrita

Insignias: 4

+1 mas insignia

Equipo

Cal Poly, Team 7-37, Regan Winter 2011 Miembro de Cal Poly, Team 7-37, Regan Winter 2011

CPSU-REGAN-W11S7G37

4 Miembros

10 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 1

Ultimos 30 días: 2

Todo El Tiempo: 710