Repara tus cosas Comunidad Tienda

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

Disassembling Palm Centro Logic Board

Introducción

This will guide you on how to disassemble the Palm Centro to get to the logic board.

Qué necesitas

  1. Disassembling Palm Centro Logic Board, Disassembling Palm Centro Battery: paso 1, imagen 1 de 2 Disassembling Palm Centro Logic Board, Disassembling Palm Centro Battery: paso 1, imagen 2 de 2

    • Press and slide open the battery cover.

    Traducir

  2. Disassembling Palm Centro Logic Board: paso 2, imagen 1 de 1

    • Caution: Turn cell phone off before removing battery!

    • Press battery to the right.

    • Then lift up battery pack to remove.

    Traducir

  3. Disassembling Palm Centro Logic Board: paso 3, imagen 1 de 1

    • Phone with battery removed

    Traducir

  4. Disassembling Palm Centro Logic Board, Back Housing: paso 4, imagen 1 de 1

    • Remove the touchpad pen from the top left corner on the back to reveal the last of 6 screws to be removed.

    Traducir

  6. Disassembling Palm Centro Logic Board: paso 5, imagen 1 de 1

    • Lift the rubber cap at the top right to reveal the sixth screw.

    • Caution: There is a small Palm sticker under the rubber cap. Tampering with or removing this sticker will void your warranty!

    • Remove the six screws using the T5 Torx screwdriver.

    Traducir

  7. Disassembling Palm Centro Logic Board: paso 6, imagen 1 de 2 Disassembling Palm Centro Logic Board: paso 6, imagen 2 de 2

    • Remove the SIM card so housing can be separated.

    Traducir

  8. Disassembling Palm Centro Logic Board: paso 7, imagen 1 de 2 Disassembling Palm Centro Logic Board: paso 7, imagen 2 de 2

    • Use a plastic pry tool to separate the bottom of the case to remove the small plastic insert.

    Traducir

  9. Disassembling Palm Centro Logic Board: paso 8, imagen 1 de 2 Disassembling Palm Centro Logic Board: paso 8, imagen 2 de 2

    • Remove the small plastic insert at the bottom of the phone.

    Traducir

  10. Disassembling Palm Centro Logic Board: paso 9, imagen 1 de 2 Disassembling Palm Centro Logic Board: paso 9, imagen 2 de 2

    • Continue with plastic pry tool all the way around the phone to remove the back housing.

    Traducir

  11. Disassembling Palm Centro Logic Board, Logic Board: paso 10, imagen 1 de 1

    • Carefully peel back the tape holding the speaker (left) and keyboard (right) connection tabs in place.

    Traducir

  12. Disassembling Palm Centro Logic Board: paso 11, imagen 1 de 1

    • Using the plastic prying tool, lift the tabs and carefully pull the contact connections out on both sides.

    • Be very careful, these electronics are delicate!

    Traducir

  13. Disassembling Palm Centro Logic Board: paso 12, imagen 1 de 1

    • Separate the logic board from the case by lifting and pulling out the bottom.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Autor

con 6 otros colaboradores

Chelsea Barackman

Miembro Desde 04/13/10

42 Reputación

3 Guías creadas

Insignias: 6

+ 3 más insignias

Equipo

Cal Poly, Team 15-49, Garner Spring 2010 Miembro de Cal Poly, Team 15-49, Garner Spring 2010

CPSU-GARNER-S10S15G49

5 Miembros

12 Guías creadas

2 comentarios

note: if you need to replace the logic board, follow this guide, insert a new board, and then follow the steps in reverse order to get a working phone.

Chelsea Barackman - Contestar

i try to on this mobile ..but cant do that, i try to on this mobile so many ways.. i want to whhy thi mobile not on and how to resolve it?

kelumaruna - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 1

Ultimos 30 días: 1

Todo El Tiempo: 3,105