Repara tus cosas Comunidad Tienda

Disassembling Insignia Flex 8 Circuit Board

Introducción

This guide should be completed before starting the other guides.

Qué necesitas

  1. Disassembling Insignia Flex 8 Circuit Board, Circuit Board: paso 1, imagen 1 de 1

    • Turn off the power to your tablet to avoid injury.

    • Position the tablet so that the screen is face down and the power button is located in the upper left hand corner.

    • Hold down the power button for five seconds until the tablet powers down.

    Traducir

  2. Disassembling Insignia Flex 8 Circuit Board: paso 2, imagen 1 de 2 Disassembling Insignia Flex 8 Circuit Board: paso 2, imagen 2 de 2

    • Remove the back casing from the screen by sliding a credit card or a similarly thin but firm object in between the casing and the screen.

    • You may need to use a spudger to initially create separation between the screen and the casing.

    • Run this object around the perimeter of the tablet until there is separation between the casing and the screen.

    • Remove the back casing and set aside.

    Traducir

  3. Disassembling Insignia Flex 8 Circuit Board: paso 3, imagen 1 de 2 Disassembling Insignia Flex 8 Circuit Board: paso 3, imagen 2 de 2

    • Peel tape off of ribbon connectors. Starting at the power button, work clockwise around the tablet.

    Traducir

  4. Disassembling Insignia Flex 8 Circuit Board: paso 4, imagen 1 de 3 Disassembling Insignia Flex 8 Circuit Board: paso 4, imagen 2 de 3 Disassembling Insignia Flex 8 Circuit Board: paso 4, imagen 3 de 3

    • To remove the camera ribbon cable, lift the flap using a spudger.

    • Pull the ribbon directly back to release it.

    Traducir

  6. Disassembling Insignia Flex 8 Circuit Board: paso 5, imagen 1 de 3 Disassembling Insignia Flex 8 Circuit Board: paso 5, imagen 2 de 3 Disassembling Insignia Flex 8 Circuit Board: paso 5, imagen 3 de 3

    • Remove the second ribbon cable by prying up the black flap using a spudger.

    • Pull the ribbon cable horizontally directly away from the battery.

    Traducir

  7. Disassembling Insignia Flex 8 Circuit Board: paso 6, imagen 1 de 3 Disassembling Insignia Flex 8 Circuit Board: paso 6, imagen 2 de 3 Disassembling Insignia Flex 8 Circuit Board: paso 6, imagen 3 de 3

    • Remove the final ribbon cable by pulling back the two black tabs on either side of the ribbon cable.

    • Pull the ribbon horizontally directly away from the battery.

    Traducir

  8. Disassembling Insignia Flex 8 Circuit Board: paso 7, imagen 1 de 2 Disassembling Insignia Flex 8 Circuit Board: paso 7, imagen 2 de 2

    • Unscrew the thirteen 4.75mm screws around the perimeter of the tablet using a PH 00 screwdriver.

    Traducir

  9. Disassembling Insignia Flex 8 Circuit Board: paso 8, imagen 1 de 2 Disassembling Insignia Flex 8 Circuit Board: paso 8, imagen 2 de 2

    • Unscrew the four 3.75mm screws and plastic washers using a PH 00 screwdriver.

    • Lift up the circuit board.

    Traducir

  10. Disassembling Insignia Flex 8 Circuit Board: paso 9, imagen 1 de 1

    • Unscrew the final two screws that were underneath the circuit board.

    • These screws are near the charging port and USB adapter.

    • These screws are also 3.75mm and can be interchanged with the second set of screws only.

    Traducir

  11. Disassembling Insignia Flex 8 Circuit Board: paso 10, imagen 1 de 1

    • Lift the circuit board and black internal mounting piece away from the screen.

    • Set the circuit board aside.

    • Be careful of the soldered antenna as you separate the pieces.

    • Be careful of the soldered ribbon that is connected to the power source. This ribbon is fragile.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

Autor

con 2 otros colaboradores

Tyler Tyrrell

Miembro Desde 03/11/15

890 Reputación

4 Guías creadas

Insignias: 17

+ 14 más insignias

Equipo

Colorado Springs, Team 5-5, Panko Spring 2015 Miembro de Colorado Springs, Team 5-5, Panko Spring 2015

UCCS-PANKO-S15S5G5

3 Miembros

12 Guías creadas

2 comentarios

Whwre can i buy the new screen

Emmanuel - Contestar

I don’t see the ssd, and way to upgrade the internal sad had?

William Henderson - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 2

Ultimos 30 días: 7

Todo El Tiempo: 4,905