Saltar al contenido principal

Disassembling Fujifilm Endeavor 100ix Outer Casing

Qué necesitas

  1. Disassembling Fujifilm Endeavor 100ix Outer Casing, Outer Casing: paso 1, imagen 1 de 1
    • Locate and remove two 6.4mm screws on the bottom of the camera with a Phillips #00 screwdriver.

  2. Disassembling Fujifilm Endeavor 100ix Outer Casing: paso 2, imagen 1 de 1
    • Locate the battery door.

  3. Disassembling Fujifilm Endeavor 100ix Outer Casing: paso 3, imagen 1 de 1
    • Locate the latch on the battery door marked by the word "BATT." Use your finger to pry it open.

  4. Disassembling Fujifilm Endeavor 100ix Outer Casing: paso 4, imagen 1 de 1
    • Remove the battery from the camera by pulling the battery door outwards.

  5. Disassembling Fujifilm Endeavor 100ix Outer Casing: paso 5, imagen 1 de 1
    • Locate and remove three black 3.80mm screws on the back of the camera with the Phillips #00 screwdriver.

  6. Disassembling Fujifilm Endeavor 100ix Outer Casing: paso 6, imagen 1 de 2 Disassembling Fujifilm Endeavor 100ix Outer Casing: paso 6, imagen 2 de 2
    • Locate and remove the 6.4mm screws located on either side of the camera with a Phillips #00 screwdriver.

  7. Disassembling Fujifilm Endeavor 100ix Outer Casing: paso 7, imagen 1 de 1
    • Locate the film door latch located on the side of the camera.

    • Insert the spudger under the latch.

    • Caution: Be careful during the following step in order to not break any parts within the camera. Prying the latch in any other direction than perpendicular may result in broken parts.

    • Pry the latch upward, applying force perpendicular to the camera.

  8. Disassembling Fujifilm Endeavor 100ix Outer Casing: paso 8, imagen 1 de 1
    • Insert the flat edge of the spudger between the gold front casing and the black back casing.

    • Pry the spudger upward until the black back casing snaps out and is dislodged on that edge of the camera.

  9. Disassembling Fujifilm Endeavor 100ix Outer Casing: paso 9, imagen 1 de 1
    • Squeeze the camera by placing a thumb on the tab marked CE.

    • Pull the back half of the camera firmly away from the camera body.

  10. Disassembling Fujifilm Endeavor 100ix Outer Casing: paso 10, imagen 1 de 1
    • Locate and remove the 3.80mm screw inside the film compartment with the Phillips #00 screwdriver.

  11. Disassembling Fujifilm Endeavor 100ix Outer Casing: paso 11, imagen 1 de 2 Disassembling Fujifilm Endeavor 100ix Outer Casing: paso 11, imagen 2 de 2
    • Pull the front cover off of the camera by lifting the tripod tab over the tripod hole.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Eric Nicolai

Miembro Desde 01/10/11

679 Reputación

6 Guías creadas

Equipo

Cal Poly, Team 13-5, Forte Winter 2011 Miembro de Cal Poly, Team 13-5, Forte Winter 2011

CPSU-FORTE-W11S13G5

5 Miembros

11 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 6

Todo El Tiempo: 1,327