Repara tus cosas Comunidad Tienda

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

Disassembling Compaq Mini 110 Keyboard

Introducción

Sticky keys? Simply just want to get rid of your keyboard? Here's how.

Qué necesitas

  1. Disassembling Compaq Mini 110 Keyboard, Battery: paso 1, imagen 1 de 2 Disassembling Compaq Mini 110 Keyboard, Battery: paso 1, imagen 2 de 2

    • Locate the battery and the battery tabs on the bottom of the Compaq Mini.

    Traducir

  2. Disassembling Compaq Mini 110 Keyboard: paso 2, imagen 1 de 3 Disassembling Compaq Mini 110 Keyboard: paso 2, imagen 2 de 3 Disassembling Compaq Mini 110 Keyboard: paso 2, imagen 3 de 3

    • Push both tabs inward simultaneously and slide the battery out.

    Traducir

  3. Disassembling Compaq Mini 110 Keyboard, RAM: paso 3, imagen 1 de 2 Disassembling Compaq Mini 110 Keyboard, RAM: paso 3, imagen 2 de 2

    • Use a Philips #0 screwdriver to unscrew the two screws covering the memory compartment on the bottom of the laptop and remove the cover.

    Traducir

  5. Disassembling Compaq Mini 110 Keyboard: paso 4, imagen 1 de 1

    • Push out the side tabs simultaneously and pull out the old RAM module.

    • When inserting a new RAM stick, be sure to evenly insert the gold pins in the same orientation that the old module was removed. While sliding the module in, press the side tabs in place.

    Traducir

  6. Disassembling Compaq Mini 110 Keyboard, Keyboard: paso 5, imagen 1 de 2 Disassembling Compaq Mini 110 Keyboard, Keyboard: paso 5, imagen 2 de 2

    • Remove the rubber pads located on the corners of your Compaq Mini.

    • There may be junk underneath it. This is residue left from the glue that held on the rubber pad. Just scrape it away to find the screw.

    Traducir

  7. Disassembling Compaq Mini 110 Keyboard: paso 6, imagen 1 de 2 Disassembling Compaq Mini 110 Keyboard: paso 6, imagen 2 de 2

    • Unscrew all the corner screws. There are four total, one under each rubber pad.

    Traducir

  8. Disassembling Compaq Mini 110 Keyboard: paso 7, imagen 1 de 2 Disassembling Compaq Mini 110 Keyboard: paso 7, imagen 2 de 2

    • Unscrew the screw for the bottom case located in the RAM compartment.

    Traducir

  9. Disassembling Compaq Mini 110 Keyboard: paso 8, imagen 1 de 2 Disassembling Compaq Mini 110 Keyboard: paso 8, imagen 2 de 2

    • Remove the three screws in the silver tabs at the back of the keyboard. The red circles show where they are located at the back of the base under the screen.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

4 personas más completaron esta guía.

Autor

con 10 otros colaboradores

alea

Miembro Desde 10/06/10

1,405 Reputación

14 Guías creadas

Insignias: 13

+ 10 más insignias

Equipo

Cal Poly, Team 22-2, Maness Fall 2010 Miembro de Cal Poly, Team 22-2, Maness Fall 2010

CPSU-MANESS-F10S22G2

6 Miembros

20 Guías creadas

3 comentarios

hi, steps 5 and 6 are not needed. not sure about removing RAM either. If I look on my removed keyboard, all I see are three places for screws - those located nearby battery socket.

Petr Gebelt - Contestar

I think steps 3,4,5,6,7 are not needed! The essential problem in removing the keyboard is not shown: how to lift the keyboard! Use the flat side or back of a screwdriver to push the metal strips shown in step 8 up (in the direction of the keyboard) to lift the keyboard. Put your fingers under the edge of the keyboard and pull gently but firmly. There is some resistance of the holding cover.

See also: https://www.youtube.com/watch?v=nELBz1VB...

Hans Donck - Contestar

Thank you so much for the link!

Alex -

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 1

Ultimos 30 días: 5

Todo El Tiempo: 16,726