Repara tus cosas Comunidad Tienda

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

Disassembling Canon Powershot SD880 Flash

Introducción

The flash device has a few delicate connections and should be handled with care.

Qué necesitas

  1. Disassembling Canon Powershot SD880 Flash, Back Cover: paso 1, imagen 1 de 3 Disassembling Canon Powershot SD880 Flash, Back Cover: paso 1, imagen 2 de 3 Disassembling Canon Powershot SD880 Flash, Back Cover: paso 1, imagen 3 de 3

    • Remove the two 2.4 mm screws on the side of the camera that are next to the LCD screen using a Phillips #00 screwdriver.

    • Remove the two 4.1 mm screws on the other side using a Phillips #00 screwdriver.

    • One screw will be located under the rubber USB flap.

    • Remove the single 2.6 mm screw from the bottom of the camera using a Phillips #00 screwdriver.

    • Slowly pull the back cover off of the camera.

    Traducir

  2. Disassembling Canon Powershot SD880 Flash, Front Cover: paso 2, imagen 1 de 3 Disassembling Canon Powershot SD880 Flash, Front Cover: paso 2, imagen 2 de 3 Disassembling Canon Powershot SD880 Flash, Front Cover: paso 2, imagen 3 de 3

    • Remove the 2.6 mm screw from the bottom of the camera using a Phillips #00 screwdriver.

    • Remove the 4.1 mm screw from the menu button side of the camera using a Phillips #00 screwdriver.

    • The two screws on the other side of the camera were already removed when the back cover was taken off.

    Traducir

  4. Disassembling Canon Powershot SD880 Flash, Top Panel: paso 3, imagen 1 de 2 Disassembling Canon Powershot SD880 Flash, Top Panel: paso 3, imagen 2 de 2

    • Unplug the green and white plugs that connect the top panel to the top of the logic board.

    • Dislodge the tab above the lens.

    • Dislodge the tab at the back.

    Traducir

  5. Disassembling Canon Powershot SD880 Flash, LCD Display: paso 4, imagen 1 de 3 Disassembling Canon Powershot SD880 Flash, LCD Display: paso 4, imagen 2 de 3 Disassembling Canon Powershot SD880 Flash, LCD Display: paso 4, imagen 3 de 3

    • Remove the two 2.9 mm screws at the top-right corner and bottom-left corner of the LCD screen using a Phillips #0 screwdriver.

    • Disconnect the ribbons that connect the screen to the camera.

    • Lift the screen off.

    Traducir

  6. Disassembling Canon Powershot SD880 Flash, Disassembling Canon Powershot SD880 Flash: paso 5, imagen 1 de 3 Disassembling Canon Powershot SD880 Flash, Disassembling Canon Powershot SD880 Flash: paso 5, imagen 2 de 3 Disassembling Canon Powershot SD880 Flash, Disassembling Canon Powershot SD880 Flash: paso 5, imagen 3 de 3

    • Use caution when removing the flash. The capacitor may still have a charge.

    • Remove 2 screws (1.75 mm) from the back with a screwdriver, disconnecting the metal guard.

    • Pull the ribbon on the top of the camera to unplug it.

    • Disconnect the white plug connected by red and black wires.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 9 otros colaboradores

Robert Manno

Miembro Desde 01/05/11

432 Reputación

4 Guías creadas

Insignias: 6

+ 3 más insignias

Equipo

Cal Poly, Team 13-3, Forte Winter 2011 Miembro de Cal Poly, Team 13-3, Forte Winter 2011

CPSU-FORTE-W11S13G3

5 Miembros

8 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 1

Ultimos 30 días: 6

Todo El Tiempo: 2,534