Introducción

Use this guide to remove the camera lens piece.

Partes

No se requieren partes.

Remove wrist strap and battery.
  • Remove wrist strap and battery.

Agregar Comentario

Remove 2 screws from each side of the camera (4 total, 0.102 in).
  • Remove 2 screws from each side of the camera (4 total, 0.102 in).

  • Remove 2 screws from the bottom on the camera (0.138 in).

  • Do not mix the 4 side screws with the 2 bottoms ones; they are different sizes.

Agregar Comentario

  • Gently pull off the front cover.

  • The plate on the side should come off.

  • Gently pull off the back cover.

Agregar Comentario

  • The cases should now be removed.

This can be a bit tricky when reassembling. All of the little tabs around the edge need to snap into their proper places, and there are three cover pieces to manage. Plus, you need to make sure that the camera/video/playback switch is properly engaged with its slider on the circuit board, otherwise you'll need to raise the back panel and reposition everything again.

Craig Bonsignore - Contestar

oh yes , i agree lol

elbala80 -

  • Remove the top-left screw above the LCD screen (0.100 in).

  • Remove the C-shaped plate from the side of the LCD screen.

Agregar Comentario

  • Remove the screw from the top-right of the LCD screen (0.098 in).

  • Remove the L-shaped bar from the right of the LCD screen.

I used this guide for a blue "made in china" version of this camera, as well as a silver "made in japan" version. The L-shaped brackets on either side of the LCD were much easier to remove for the blue one, but I was able to get them out for the silver one also with some additional coaxing. There were more pronounced tabs/notches securing the brackets to the adjacent frame on the silver one.

Craig Bonsignore - Contestar

  • Use the spudger to remove the L-shaped bar from the left-side of the LCD screen.

Agregar Comentario

  • Use tweezers to remove the connector ribbon from the top-left corner above the LCD screen.

  • Be gentle. This ribbon should stay attached to the screen.

There is a hole in the reinforced "plug" end of the LCD cable shown in Step 8. You can use a dental-type pick to remove and replace the plug easily.

Edward Pinnell - Contestar

  • Use a spudger to lift the connector lock (black flap) at the end of the larger LCD connector ribbon on the front side of the camera.

  • Use the tweezers to lift this ribbon.

  • Use the tweezers to gently peel this ribbon from the one underneath it.

Agregar Comentario

  • The LCD screen should now be removed.

Agregar Comentario

  • Remove the screw located on the side of the camera (0.072 in).

Agregar Comentario

  • Use the spudger to remove the lens ribbon from the circuit board.

  • Use the spudger to lift the ribbon.

  • This ribbon is connected to the lens, but the flash assembly ribbon is underneath it.

Agregar Comentario

  • Disconnect the flash assembly ribbon.

  • The flash assembly ribbon is located underneath the lens assembly ribbon.

Agregar Comentario

  • Remove the flash assembly, which includes the capacitor. If it resists, note the small hook on the right side near the bottom.

  • Be careful when taking out the capacitor. It could shock you.

Agregar Comentario

  • The capacitor should now be removed.

Agregar Comentario

  • Remove 4 screws from silver plate (0.106 in).

Agregar Comentario

  • Use spudger to lift the second lens ribbon.

  • Remember the first ribbon was removed while taking out the flash assembly.

Agregar Comentario

  • Use spudger to carefully lift the LED light off the upper-left corner of the lens.

This step omits the removal of the shutter release assembly shown in position in Step 17. Picture in Step 18 shows release assembly removed. Release assembly can be removed and set aside taking care to not disturb connection wires to expose LED light so it can be pried off the lens assembly as shown in second photo of this step.

Mike Lione - Contestar

  • Remove the lens.

Agregar Comentario

  • The camera lens should now be removed.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

12 personas más completaron esta guía.

Tyler Grossheim

Miembro Desde 25/01/11

1,359 Reputación

6 Guías creadas

Equipo

Cal Poly, Team 3-32, Regan Winter 2011 Miembro de Cal Poly, Team 3-32, Regan Winter 2011

CPSU-REGAN-W11S3G32

3 Miembros

8 Guías creadas

How do you CLEAN the lens?

Christian - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 12

Últimos 30 Días: 68

Todo El Tiempo: 16,602