Saltar al contenido principal

Qué necesitas

  1. Disassembling Canon PowerShot A590 IS Front Cover, Batteries: paso 1, imagen 1 de 2 Disassembling Canon PowerShot A590 IS Front Cover, Batteries: paso 1, imagen 2 de 2
    • The battery hatch is on the bottom of the camera.

    • CAUTION: Locate the switch to open the hatch and push gently toward the front of the camera. Too much force can break the hatch.

    • While the switch is pushed forward, pull the cover away from the camera.

  2. Disassembling Canon PowerShot A590 IS Front Cover: paso 2, imagen 1 de 1
    • This camera requires AA batteries.

    • To remove batteries, simply allow them to fall out of the camera.

    • Use a fingernail to lift the clock battery out of the camera.

  3. Disassembling Canon PowerShot A590 IS Front Cover: paso 3, imagen 1 de 1
    • When replacing the AA batteries, verify they are oriented correctly by following the (+) and (-) signs on the camera.

  4. Disassembling Canon PowerShot A590 IS Front Cover, Back Cover: paso 4, imagen 1 de 1
    • Remove the screw located under the rubber flap on the left side of the camera using a Phillips #00 screwdriver.

  5. Disassembling Canon PowerShot A590 IS Front Cover: paso 5, imagen 1 de 1
    • Remove the two screws located on the other side of the camera using a Phillips #00 screwdriver.

  6. Disassembling Canon PowerShot A590 IS Front Cover: paso 6, imagen 1 de 1
    • Remove the three screws located at the bottom of the camera using a Phillips #00 screwdriver.

  7. Disassembling Canon PowerShot A590 IS Front Cover: paso 7, imagen 1 de 1
    • Open the battery cover.

    • Using the iFixit opening tool, push up gently around all edges of the camera.

  8. Disassembling Canon PowerShot A590 IS Front Cover, Remove Lens Cover: paso 8, imagen 1 de 1
    • Press and hold down the button shown in the blue circle.

    • While pressing the button, rotate the lens cover in a counter-clockwise direction to remove it.

  9. Disassembling Canon PowerShot A590 IS Front Cover, Remove Front Cover: paso 9, imagen 1 de 2 Disassembling Canon PowerShot A590 IS Front Cover, Remove Front Cover: paso 9, imagen 2 de 2
    • Remove the front cover of the camera.

    • This may require a bit of force.

Conclusión

To reassemble your device, follow these instructions in reverse order.

5 personas más completaron esta guía.

Zach

Miembro Desde 11/10/10

281 Reputación

6 Guías creadas

Equipo

Cal Poly, Team 9-19, Regan Fall 2010 Miembro de Cal Poly, Team 9-19, Regan Fall 2010

CPSU-REGAN-F10S9G19

4 Miembros

14 Guías creadas

3 comentarios

The photos do not show a camera strap, and the instructions don't mention it. Before starting disassembly, I advise removing the camera strap. It make it easier to remove and re-attach the back cover.

jwoconnor - Contestar

A handy guide. I had an A590IS with a broken battery door latch on the camera body, and I managed to obtain a dead A590IS with a fully intact latch for free. So using this guide I swapped the body shells over! All fixed and working again!

brianinnes81 - Contestar

l cannot get an answer to my question on why my Canon A590 will not power on.

burks817 - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 2

Ultimos 30 días: 33

Todo El Tiempo: 14,094