Repara tus cosas Comunidad Tienda

Digital2 D2-861G Charging Port Replacement

Introducción

This guide will be showing you how to replace the charging port for the Digital2 D2-861G model. Be sure to carefully remove parts to avoid damaging the device.

Qué necesitas

  1. Digital2 D2-861G Charging Port Replacement, Motherboards: paso 1, imagen 1 de 1

    • Working on your device while powered on may result in electric shock. Make sure to unplug and power down your device before you begin.

    • Place your device on a soft cloth to avoid scratching the screen.

    • Flip your device over so back panel is facing upwards.

    Editar

  2. Digital2 D2-861G Charging Port Replacement: paso 2, imagen 1 de 1

    • Do not use a lot of force as it can break the clips or the back panel.

    • Insert spudger in the slot below the micro SD card.

    • You should hear clips releasing as you pry along the edges.

    • With the spudger tool, run along the edges of the backing undoing 20 plastic clips.

    Editar

  3. Digital2 D2-861G Charging Port Replacement: paso 3, imagen 1 de 3 Digital2 D2-861G Charging Port Replacement: paso 3, imagen 2 de 3 Digital2 D2-861G Charging Port Replacement: paso 3, imagen 3 de 3

    • Locate the gold colored ZIF (Zero insertion force) connector and disconnect it from the motherboard.

    • To disconnect the ZIF connector, go under the black tab and lift up. Then pull the connector out.

    • Locate the bundled cable connector and disconnect it by simply pulling it gently or using a spudger.

    • Disconnecting the bundled cable connector helps avoid short circuiting anything on the device.

    Editar

  5. Digital2 D2-861G Charging Port Replacement: paso 4, imagen 1 de 3 Digital2 D2-861G Charging Port Replacement: paso 4, imagen 2 de 3 Digital2 D2-861G Charging Port Replacement: paso 4, imagen 3 de 3

    • Make sure to have your magnetic board to hold your screws.

    • Remove two 3.51mm screws that are located on the top corners with your Phillips #00 screwdriver.

    • Next, unplug the ZIF connector by going under the black tab and simply lift up.

    • Slide the connector out with the pointed side of the spudger.

    Editar

  6. Digital2 D2-861G Charging Port Replacement: paso 5, imagen 1 de 3 Digital2 D2-861G Charging Port Replacement: paso 5, imagen 2 de 3 Digital2 D2-861G Charging Port Replacement: paso 5, imagen 3 de 3

    • This step is optional if you want to remove the metal casing.

    • Insert the pointed side of the spudger in the corner and gently lift.

    • Once one side is lifted, use your fingers and with little force, lift up to remove the case.

    Editar

  7. Digital2 D2-861G Charging Port Replacement: paso 6, imagen 1 de 1

    • Use little force or else you risk breaking the motherboard.

    • Watch out for the ZIF connector!

    • There is a white clip holding the motherboard.

    • To remove the motherboard, grab the component on the top left and gently lift while pushing or pulling to the right.

    Editar

  8. Digital2 D2-861G Charging Port Replacement, Charging Port: paso 7, imagen 1 de 1
    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 1

Ultimos 30 días: 1

Todo El Tiempo: 237