Saltar al contenido principal

Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement

Qué necesitas

  1. Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement, Unplug: paso 1, imagen 1 de 1
    • Before you begin, remember to disconnect the mains plug.

  2. Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement: paso 2, imagen 1 de 2 Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement: paso 2, imagen 2 de 2
    • Remove the three screws from the pad.

  3. Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement: paso 3, imagen 1 de 3 Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement: paso 3, imagen 2 de 3 Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement: paso 3, imagen 3 de 3
    • Be careful to keep the three small marbles.

  4. Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement: paso 4, imagen 1 de 2 Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement: paso 4, imagen 2 de 2
    • Unscrew the screws to open the shell.

  5. Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement: paso 5, imagen 1 de 1
    • Remove the orange cap.

    • Using a screwdriver lift the brushes.

  6. Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement: paso 7, imagen 1 de 3 Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement: paso 7, imagen 2 de 3 Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement: paso 7, imagen 3 de 3
    • Remove the carbon from its housing then take it out.

    • Using pliers, fold down the small tab.

  7. Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement: paso 8, imagen 1 de 1
    • Replace the new carbon in its carbon holder.

    • Reconnect the carbon, test if the carbon slides well inside.

  8. Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement: paso 10, imagen 1 de 1
    • Replace the coals in their housing.

  9. Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement: paso 11, imagen 1 de 1
    • Before closing, check that no cable is blocked and that each part is in its place.

    • Replace the screws on the hull.

  10. Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement: paso 12, imagen 1 de 3 Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement: paso 12, imagen 2 de 3 Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement: paso 12, imagen 3 de 3
    • Replace the retaining flange, be careful to have the three small balls.

  11. Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement: paso 13, imagen 1 de 2 Dexter 300W Corded Delta Sander - 300DS2.5 Carbon Replacement: paso 13, imagen 2 de 2
    • Tighten the three screws of the retaining plate then that of the pad.

Conclusión

To reassemble follow guide through or in reverse

Un agradecimiento especial a estos traductores:

fr en

100%

¡ HelloMacOS nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Céline Chemineau

Miembro Desde 01/29/20

16,554 Reputación

95 Guías creadas

Equipo

Leroy Merlin Miembro de Leroy Merlin

Community

36 Miembros

239 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 10

Todo El Tiempo: 154