Introducción
Tutorial de desmontaje básico para iPhone X.
Qué necesitas
Resumen del Video
-
-
Presione el botón de activación y el de reducción de volumen para apagar el teléfono.
-
-
-
Usa el destornillador Pentalobe para quitar los tornillos del puerto de carga. Calentar el teléfono con una pistola de aire caliente permitirá que el teléfono se abra más fácilmente.
-
-
-
Desatornilla los 5 tornillos con un destornillador #Y000 mostrados en la imagen de abajo.
-
Estos tornillos son de diferente tamaño así que ten un registro de donde van.
-
Suelte la batería / pantalla LCD / digitalizador / conectores de altavoz con un spudger.
It’s an OLED screen, not LCD..
need the screw sizes if anybody has them
Hi Alan, you can find the screw sizes in step 13 of our screen replacement guide.
Hello, I need help please Is the same screwdriver used for all 5 screws? that is to say the Tri Point Y000
-
-
-
Quite los 3 tornillos Y000 y caliente el cable flexible con una pistola de aire caliente para poder quitar fácilmente el auricular
-
-
-
-
Remueve los dos tornillos Phillips #PH00 y remueve la placa metálica, desconecta los conectores de las cámaras posteriores
-
Estos tornillos también son de diferente tamaño
WE need a picture of all the part that need to be removed here… if the rear cameras (the square silver shapes) need to be removed before the motherboard, direction as to that is needed.
Motherboard does not need to come out yet
Notice the screw furthest left in picture. There is a connection to the front-facing cameras that need to be gently popped up to remove the antenna.
the leftmost screw in the picture is the longer one
-
-
-
Libera todos los conectores de la placa madre con un spudger
-
Desatornilla los 3 tornillos Phillips #PH00 en la placa madre y retírala.
I feel like the last ribbon cable towards the top of the board needs to be addressed here. It's the cable right under the IR sensor for facial recognition in step five. It completely hid itself from my view and I feel like this can happen to someone else. It would be awful to destroy that cable or anything else.
I can’t get the motherboard off because of that hidden flat cable at the top of the phone! I see no way to disengage it. Am I screwed?
So, yeah. This step in particular is missing about three more steps, without which you are in danger of tearing the IR sensor. So here’s the missing info. After releasing the connectors from the board:
* remove the two Phillips screws, under the top lip of the phone chassis, holding the front camera assy in place.
* Pull the camera assy forward just enough to loosen the IR cable that lays across the board. No need to un-stick the ribbon cables from the chassis.
* use a spudger to disconnect the antenna cable from the board, directly under the IR cable.
* gently remove the laminate board while carefully pushing the ribbon connectors out of the way with a spudger.
the leftmost screw (in the picture) is longer than the rightmost one
-
-
-
Quitar los 8 tornillos de la placa de retención y luego retire la placa teniendo cuidado de no romper el conector pequeño , que se conecta justo debajo de el motor de vibración háptico. (Taptic Engine)
-
Retire el altavoz y el motor de vibración háptico. (Taptic Engine)
-
-
-
Tirando de 4 adhesivos de batería con unas pinzas, podemos retirar la batería.
-
-
-
Calentar la cámara frontal con una pistola de calor hará que sea fácil de quitar
-
-
-
Suelte los 4 tornillos en el marco que se muestra en la imagen
-
Calentando el cable flexible del puerto de carga, entonces podemos quitarlo fácilmente
What size and type of screw is the one on the side that holds the interconnect cable in?
-
-
-
Suelte los 7 tornillos del cable flexible Wi-Fi
-
Calentar el cable flexible con una pistola de calor hace que sea más fácil de quitar
need screw description, and tiny piece placement (three)
-
-
-
Quitar los 3 tornillos que figuran en la imagen de referencia correspondientes al botón de inicio
-
Para que se pueda retirar fácilmente el cable flexible, debe calentarlo con una pistola de calor.
-
Para volver a armar su dispositivo, siga estas instrucciones en orden inverso.
Para volver a armar su dispositivo, siga estas instrucciones en orden inverso.
Cancelar: No complete esta guía.
128 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
25 comentarios
It's good
The iPhone X assemble video: https://youtu.be/E5jyuxgpE_g
What About the backside ? I heard that when the backside is shattered, it’s almost impossible to repair, because of the glue that holds the backside and parts together ?
Hi avdk, we don’t tear down the back glass but we will pay attention to this question. If there is a definite answer, I will reply to you .Thank you.
Mandy -
The back glass is heavily glued down, and sandwiched between the metal chassis and the rear camera cover (which are welded together). So far as we can tell, there is no practical way to replace the back glass. If it shatters, you’ll have to either live with it, or remove every component and replace the entire enclosure. If you take it to Apple, they will charge you for an out-of-warranty repair (roughly half the original retail price of the phone) and simply replace the entire phone. Check the teardown for some images of the back glass coming off.
You can replace the back glass cover of the iPhone X. We do it at work. It takes like 2 hours of heating though but its changeable.
Cristell -
Now there is a machine for remove the iPhone 8/8P/X back glass. Also there are many videos on YouTube about how to remove the back glass easily.
Mandy -
Where can I find your work surface? It looked really organized and had spots for your screwdrivers?
Hi Mike, you can get it in Etrade Supply. Here is the links you need:https://www.etradesupply.com/catalog/pro...
https://www.etradesupply.com/catalog/pro.... May this can help you!
Mandy -
What are the specs for each screw in the iPhone X?
Thank you. I love the resources that you guys put together and the detailed instructions.
While the E-Trade Supply video is fantastic, anybody tinkering with the phone may also want to have a look at the video on JerryRigEverything (https://www.youtube.com/watch?v=c97ILI7T...) to reinforce their understanding of the tear-down process.
Thank you for this. This is my first time to DIY with my iPhone. I wasn’t able to figure things out without the second video. One issue is that the tools recommended for this repair are incomplete. I ordered a toolkit that met the requirements - but it did not include the tool that has suction cups on both ends to open it easily. That wasn’t on the list. It was only in their video.
Not a complete guide to follow. Seeing other teardowns, I notice steps are out of logical order and / or missing. The descriptions lack clarity and left retracing my steps to remove parts not previously mentioned. Then there was not caution of the tweezers possibly poking the battery or by removing the volume flex cable from the wireless charging coil requires re-micro-soldering or replacing the charging coil + flex cable.
what about the bluetooth antenna
Hi,
Auf der Innenseite vom backcover, direkt unter dem Logic Board befindet sich eine schwarze klebe abschirmung.
Wozu dient diese genau? Bzw. handelt es sich dabei überhaupt um eine Art Abschirmung? Was für Auswirkungen hat es, wen bei einem komplettem back cover Tausch dieses klebe pad nicht übernommen wird? Strahlungs schutz folie? Oder doch abschirmung des logic Board bei verwendung der Induktions Ladestation?
Mfg marvin
I don't even understand some of the details in this article, but there is some amazing information for me. I am aiming to build an engaging attractive website named wordle unlimited wordle and I got some ideas after reading this article. Thank you.
What type of heat gun do you use and what temperature is needed?