Repara tus cosas Comunidad Tienda

Dell Studio 1737 Palmrest Assembly Replacement

Qué necesitas

  1. Dell Studio 1737 Palmrest Assembly Replacement, Battery: paso 1, imagen 1 de 2 Dell Studio 1737 Palmrest Assembly Replacement, Battery: paso 1, imagen 2 de 2

    • Slide the battery release slider all the way to the right and push the battery straight out of the back of the computer

    Editar

  2. Dell Studio 1737 Palmrest Assembly Replacement, Back Panel: paso 2, imagen 1 de 3 Dell Studio 1737 Palmrest Assembly Replacement, Back Panel: paso 2, imagen 2 de 3 Dell Studio 1737 Palmrest Assembly Replacement, Back Panel: paso 2, imagen 3 de 3

    • Unscrew the 8 Phillips head screws marked in the photo.

    • Even when the screws are fully detached, they will not come out of the panel.

    • Use a plastic opening tool to pry the panel away from the laptop body.

    • Lift the panel up and away.

    Editar

  3. Dell Studio 1737 Palmrest Assembly Replacement, Keyboard: paso 3, imagen 1 de 1

    • Use a plastic opening tool to detach the internal clips (marked with red boxes in photo) and release the small plastic panel above the keyboard

    • This panel doesn't come off just yet, this step is just to make it easier when it comes time to remove it

    Editar

  4. Dell Studio 1737 Palmrest Assembly Replacement: paso 4, imagen 1 de 1

    • Remove the 4mm ph1 screw under the battery

    Editar

  5. Dell Studio 1737 Palmrest Assembly Replacement: paso 5, imagen 1 de 3 Dell Studio 1737 Palmrest Assembly Replacement: paso 5, imagen 2 de 3 Dell Studio 1737 Palmrest Assembly Replacement: paso 5, imagen 3 de 3

    • Pry black panel away from laptop body starting at the base of the screen

    • Be careful when flipping the panel over, as the panel is still attached by the fragile ribbon cable

    • Flip the panel over onto the keyboard

    • Detach the ribbon cable from the motherboard as shown

    Editar

  7. Dell Studio 1737 Palmrest Assembly Replacement: paso 6, imagen 1 de 1

    • Starting at the top where you just removed the black panel, pry the black bezel away from the outside of the keyboard

    Editar

  8. Dell Studio 1737 Palmrest Assembly Replacement: paso 7, imagen 1 de 2 Dell Studio 1737 Palmrest Assembly Replacement: paso 7, imagen 2 de 2

    • Use a small screwdriver to take out the 4 4mm ph1 screws along the top of the keyboard

    • Lift from the top of the keyboard and flip it over onto the palmrest

    • Again, be very careful of the ribbon cable attaching it, as these are easily damaged

    Editar

  9. Dell Studio 1737 Palmrest Assembly Replacement: paso 8, imagen 1 de 2 Dell Studio 1737 Palmrest Assembly Replacement: paso 8, imagen 2 de 2

    • Remove the ribbon cable as shown

    Editar

  10. Dell Studio 1737 Palmrest Assembly Replacement, Palmrest Assembly: paso 9, imagen 1 de 1

    • Remove the 8 8mm ph1 philips head screws (red)

    • Remove also the one 4mm ph 1 philips head screw (blue)

    Editar

  11. Dell Studio 1737 Palmrest Assembly Replacement: paso 10, imagen 1 de 1

    • Pull the antenna cables off of the wireless card(s)

    • Depending on the setup of the laptop, there may be as many as 3 wireless cards, and all of the antennas must be detached

    Editar

  12. Dell Studio 1737 Palmrest Assembly Replacement: paso 11, imagen 1 de 1

    • Remove the two 4mm ph1 screws along the black panel to which the speakers are attached

    • One of the screws is located under a wire channel and can be difficult to spot, look closely at the photo to make sure you get the right one

    Editar

  13. Dell Studio 1737 Palmrest Assembly Replacement: paso 12, imagen 1 de 1

    • Unplug the 6 marked cables from the motherboard

    • The connectors that aren't standard plugs or ribbon cables are detached by simply lifting straight up away from the computer

    • Pull the antenna cables out through the motherboard, free them from their cable channels, and route them in such a way that they don't interfere with the next step

    Editar

  14. Dell Studio 1737 Palmrest Assembly Replacement: paso 13, imagen 1 de 1

    • Using a plastic opening tool, pry the palmrest away from the body of the laptop all the way from one hinge to the other, disconnecting all of the internal clips along the way

    • Lift the palmrest up and off of the laptop

    • A small piece of this panel will get caught under the attachment point for the left hinge, just slide the panel slightly to the right to free it

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

Autor

con 2 otros colaboradores

Seth Stark

Miembro Desde 03/06/17

230 Reputación

1 Guía escrita

Insignias: 7

+ 4 más insignias

Equipo

UMass Dartmouth, Team S8-G4, Catania Spring 2017 Miembro de UMass Dartmouth, Team S8-G4, Catania Spring 2017

UMASSD-CATANIA-S17S8G4

Miembros de 3

8 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 3

Ultimos 30 días: 3

Todo El Tiempo: 418