Repara tus cosas Comunidad Tienda

Dell Alienware 13 R2 Status-Light Board Replacement

Introducción

In this guide, we will show you how to remove and replace the status light board.

Qué necesitas

  1. Dell Alienware 13 R2 Status-Light Board Replacement, Turning Over the PC: paso 1, imagen 1 de 1

    • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer After working inside your computer, follow the instructions in After Working Inside Your Computer For more safety best practices, see the regulatory compliance home page.

    • Close the display and turn the computer over.

    Traducir

  2. Dell Alienware 13 R2 Status-Light Board Replacement, Loosen the screws: paso 2, imagen 1 de 1

    • Loosen the captive screws that secure the base panel to the computer base.

    Traducir

  3. Dell Alienware 13 R2 Status-Light Board Replacement, Releasing the Tabs: paso 3, imagen 1 de 1

    • Using a plastic scribe, gently release the tabs that secure the base panel to the computer base.

    Traducir

  4. Dell Alienware 13 R2 Status-Light Board Replacement, Disconnecting the Battery Cable: paso 4, imagen 1 de 2 Dell Alienware 13 R2 Status-Light Board Replacement, Disconnecting the Battery Cable: paso 4, imagen 2 de 2

    • Disconnect the battery cable from the battery-cable connector.

    • Turn the computer over.

    Traducir

  5. Dell Alienware 13 R2 Status-Light Board Replacement, Power Button: paso 5, imagen 1 de 1

    • Press and hold the power button for 5 seconds to ground the system board.

    Traducir

    • Connect the battery cable to the battery-cable connector.

    Traducir

  7. Dell Alienware 13 R2 Status-Light Board Replacement, Aligning the tabs: paso 7, imagen 1 de 1

    • Align the tabs on the base panel with the slots on the computer base and snap the base panel into place.

    Traducir

  8. Dell Alienware 13 R2 Status-Light Board Replacement, Tighten the screws: paso 8, imagen 1 de 1

    • Tighten the captive screws that secure the base panel to the computer base.

    Traducir

  9. Dell Alienware 13 R2 Status-Light Board Replacement, Removing the Screws: paso 9, imagen 1 de 2 Dell Alienware 13 R2 Status-Light Board Replacement, Removing the Screws: paso 9, imagen 2 de 2

    • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

    • Remove the screws that secure the solid-state drive bracket to the solid-state drive assembly.

    Traducir

  10. Dell Alienware 13 R2 Status-Light Board Replacement, Peel off Computer Base Tabs: paso 10, imagen 1 de 2 Dell Alienware 13 R2 Status-Light Board Replacement, Peel off Computer Base Tabs: paso 10, imagen 2 de 2

    • Using the pull tab, pivot the solid-state drive bracket and peel off the bracket from the tabs on the computer base.

    Traducir

  11. Dell Alienware 13 R2 Status-Light Board Replacement, Disconnecting the Solid-State Drive Cable: paso 11, imagen 1 de 1

    • Using the pull tab, disconnect the solid-state drive cable from the system board.

    Traducir

  12. Dell Alienware 13 R2 Status-Light Board Replacement, Removing the Solid-State Drive: paso 12, imagen 1 de 2 Dell Alienware 13 R2 Status-Light Board Replacement, Removing the Solid-State Drive: paso 12, imagen 2 de 2

    • Remove the screws that secure the solid-state drive assembly to the computer base.

    Traducir

  13. Dell Alienware 13 R2 Status-Light Board Replacement, Lifting the Solid-State Assembly: paso 13, imagen 1 de 1

    • Lift the solid-state drive assembly off the computer base.

    Traducir

  14. Dell Alienware 13 R2 Status-Light Board Replacement, Remove the Screw: paso 14, imagen 1 de 1

    • Remove the screw that secures the solid-state drive to the solid-state drive assembly.

    Traducir

  15. Dell Alienware 13 R2 Status-Light Board Replacement, Lift the Solid-State Assembly.: paso 15, imagen 1 de 2 Dell Alienware 13 R2 Status-Light Board Replacement, Lift the Solid-State Assembly.: paso 15, imagen 2 de 2

    • Slide and lift the solid-state drive off the solid-state drive assembly.

    Traducir

  16. Dell Alienware 13 R2 Status-Light Board Replacement, The New Solid-State Drive: paso 16, imagen 1 de 1

    • Slide the NEW solid-state drive into the slot on the solid-state drive assembly.

    Traducir

  17. Dell Alienware 13 R2 Status-Light Board Replacement, Screw Replacement: paso 17, imagen 1 de 2 Dell Alienware 13 R2 Status-Light Board Replacement, Screw Replacement: paso 17, imagen 2 de 2

    • Replace the screw that secures the solid-state drive to the solid-state drive assembly.

    Traducir

  18. Dell Alienware 13 R2 Status-Light Board Replacement, Align the Screws: paso 18, imagen 1 de 2 Dell Alienware 13 R2 Status-Light Board Replacement, Align the Screws: paso 18, imagen 2 de 2

    • Align the screw holes on the solid-state drive assembly with the screw holes on the computer base.

    Traducir

  19. Dell Alienware 13 R2 Status-Light Board Replacement, Replace the Screws: paso 19, imagen 1 de 1

    • Replace the screws that secure the solid-state drive assembly to the computer base.

    Traducir

  21. Dell Alienware 13 R2 Status-Light Board Replacement, Connect the Cable to the System Board: paso 20, imagen 1 de 1

    • Connect the solid-state drive cable to the system board.

    Traducir

  22. Dell Alienware 13 R2 Status-Light Board Replacement, Align the Screw Holes: paso 21, imagen 1 de 1

    • Align the screw holes on the solid-state drive bracket with the screw holes on the solid-state drive assembly.

    Traducir

  23. Dell Alienware 13 R2 Status-Light Board Replacement, Replace the Screws: paso 22, imagen 1 de 2 Dell Alienware 13 R2 Status-Light Board Replacement, Replace the Screws: paso 22, imagen 2 de 2

    • Replace the screws that secure the solid-state drive bracket to the solid-state drive assembly.

    Traducir

  24. Dell Alienware 13 R2 Status-Light Board Replacement, Lifting the Latches: paso 23, imagen 1 de 1

    • Lift the latches and disconnect the keyboard and keyboard-backlight cables from the system board.

    Traducir

  25. Dell Alienware 13 R2 Status-Light Board Replacement, Remove the Screws: paso 24, imagen 1 de 1

    • Remove the screws that secure the palm-rest assembly to the computer base.

    Traducir

  26. Dell Alienware 13 R2 Status-Light Board Replacement, Lift the Computer Base: paso 25, imagen 1 de 1

    • Lift the computer base slightly and push the release tabs on the palm-rest assembly until it pops out.

    Traducir

    • Turn the computer over and open the display as far as possible.

    Traducir

  28. Dell Alienware 13 R2 Status-Light Board Replacement, Prying the Palm-Rest Assembly: paso 27, imagen 1 de 1

    • Using a plastic scribe, pry up along the edges of the palm-rest assembly.

    Traducir

  29. Dell Alienware 13 R2 Status-Light Board Replacement, Lift the Palm-Rest Assembly: paso 28, imagen 1 de 1

    • Gently lift the palm-rest assembly and turn it over.

    Traducir

  30. Dell Alienware 13 R2 Status-Light Board Replacement, Lift the Connector Latch: paso 29, imagen 1 de 2 Dell Alienware 13 R2 Status-Light Board Replacement, Lift the Connector Latch: paso 29, imagen 2 de 2

    • Lift the connector latch and disconnect the power-button board cable from the system board.

    Traducir

  31. Dell Alienware 13 R2 Status-Light Board Replacement, Lift the Palm-Rest Assembly: paso 30, imagen 1 de 1

    • Lift the palm-rest assembly off the computer base.

    Traducir

  32. Dell Alienware 13 R2 Status-Light Board Replacement, Removing: paso 31, imagen 1 de 1

    • Remove the keyboard.

    • Remove the power-button board.

    • Remove the status-light board.

    • Remove the Touchpad.

    Traducir

    • Replace the touchpad.

    • Replace the status-light board.

    • Replace the power-button board.

    • Replace the keyboard.

    Traducir

    • Connect the power-button board cable to the system board.

    Traducir

  35. Dell Alienware 13 R2 Status-Light Board Replacement, Align the Palm-Rest Assembly: paso 34, imagen 1 de 1

    • Align the palm-rest assembly on the computer base and snap it into place.

    Traducir

    • Close the display and turn the computer over.

    Traducir

    • Replace the screws that secure the palm-rest assembly to the computer base.

    Traducir

    • Connect the keyboard cable and the keyboard-backlight cable to the system board.

    Traducir

  39. Dell Alienware 13 R2 Status-Light Board Replacement, Lift the Connector Latches: paso 38, imagen 1 de 1

    • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

    • Lift the connector latches and disconnect the touchpad cable and the status-light cable from the power-button board.

    Traducir

  40. Dell Alienware 13 R2 Status-Light Board Replacement, Peel the Touchpad Cable: paso 39, imagen 1 de 2 Dell Alienware 13 R2 Status-Light Board Replacement, Peel the Touchpad Cable: paso 39, imagen 2 de 2

    • Peel the touchpad cable and status-light cable off the keyboard bracket.

    Traducir

  41. Dell Alienware 13 R2 Status-Light Board Replacement, Remove the Screws: paso 40, imagen 1 de 1

    • Remove the screws that secure the keyboard bracket to the palm-rest assembly.

    Traducir

  42. Dell Alienware 13 R2 Status-Light Board Replacement, Lifting the Keyboard Bracket: paso 41, imagen 1 de 1

    • Lift the keyboard bracket off the palm-rest assembly.

    Traducir

  43. Dell Alienware 13 R2 Status-Light Board Replacement, Remove the Screws: paso 42, imagen 1 de 1

    • Remove the screws that secure the keyboard to the palm-rest assembly.

    Traducir

  44. Dell Alienware 13 R2 Status-Light Board Replacement, Slide and Lift the Keyboard: paso 43, imagen 1 de 1

    • Slide and lift the keyboard, along with the cables, off the palm-rest assembly.

    Traducir

  45. Dell Alienware 13 R2 Status-Light Board Replacement, Align the Screw Holes: paso 44, imagen 1 de 1

    • Align the screw holes on the NEW keyboard with the screw holes on the palm-rest assembly.

    Traducir

  46. Dell Alienware 13 R2 Status-Light Board Replacement, Replace the Screws: paso 45, imagen 1 de 1

    • Replace the screws that secure the keyboard to the palm-rest assembly.

    Traducir

    • Align the screw holes on the keyboard bracket with the screw holes on the palm-rest assembly.

    Traducir

    • Replace the screws that secure the keyboard bracket to the palm-rest assembly.

    Traducir

    • Adhere the touchpad cable and status-light cable to the keyboard bracket.

    Traducir

    • Slide the touchpad cable and the status-light cable into their respective connectors on the power-button board and press down the latches to secure the cables.

    Traducir

  51. Dell Alienware 13 R2 Status-Light Board Replacement, Disconnecting the Status-Light Board Cable: paso 50, imagen 1 de 2 Dell Alienware 13 R2 Status-Light Board Replacement, Disconnecting the Status-Light Board Cable: paso 50, imagen 2 de 2

    • WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.

    • Lift the connector latch and disconnect the status-light board cable from the status-light board.

    Traducir

  52. Dell Alienware 13 R2 Status-Light Board Replacement, Remove the Screw: paso 51, imagen 1 de 2 Dell Alienware 13 R2 Status-Light Board Replacement, Remove the Screw: paso 51, imagen 2 de 2

    • Remove the screw that secures the status-light board to the palm-rest assembly.

    Traducir

    • Lift the status-light board off the palm-rest assembly.

    Traducir

  54. Dell Alienware 13 R2 Status-Light Board Replacement, Sliding the Cable: paso 53, imagen 1 de 2 Dell Alienware 13 R2 Status-Light Board Replacement, Sliding the Cable: paso 53, imagen 2 de 2

    • Slide the status-light board cable into the status-light board connector and press down the latch to secure the cable.

    Traducir

  55. Dell Alienware 13 R2 Status-Light Board Replacement, Align the Screw Hole: paso 54, imagen 1 de 1

    • Align the screw hole on the status-light board with the screw hole on the palm-rest assembly.

    Traducir

  56. Dell Alienware 13 R2 Status-Light Board Replacement, Replace the Screw: paso 55, imagen 1 de 1

    • Replace the screw that secures the status-light board to the palm-rest assembly.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 2 otros colaboradores

Terrence15

Miembro Desde 12/18/17

79,091 Reputación

441 Guías creadas

Insignias: 28

+ 25 más insignias

Equipo

RampUP America, Inc. Miembro de RampUP America, Inc.

Community

42 Miembros

1,985 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 1

Todo El Tiempo: 96