Saltar al contenido principal

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

DBPOWER T20 Lens Replacement

Qué necesitas

  1. DBPOWER T20 Lens Replacement, DBPOWER T20 Disassembly: paso 1, imagen 1 de 1
    • Flip the device and lay flat.

  2. DBPOWER T20 Lens Replacement: paso 2, imagen 1 de 1
    • Remove the four (9 mm) screws with a PH2 screwdriver.

    • Remove the two (7 mm) located with a PH2 screwdriver.

  3. DBPOWER T20 Lens Replacement: paso 3, imagen 1 de 3 DBPOWER T20 Lens Replacement: paso 3, imagen 2 de 3 DBPOWER T20 Lens Replacement: paso 3, imagen 3 de 3
    • Flip the device over and pry the top off with a plastic opening tool.

  4. DBPOWER T20 Lens Replacement: paso 4, imagen 1 de 1
    • Remove the ribbon cable connecting the motherboard to the button control board by gently pulling it from its connector.

  5. DBPOWER T20 Lens Replacement: paso 5, imagen 1 de 2 DBPOWER T20 Lens Replacement: paso 5, imagen 2 de 2
    • Remove four (6 mm) screws connecting the motherboard using a J0 screwdriver.

  6. DBPOWER T20 Lens Replacement: paso 6, imagen 1 de 3 DBPOWER T20 Lens Replacement: paso 6, imagen 2 de 3 DBPOWER T20 Lens Replacement: paso 6, imagen 3 de 3
    • Remove the two cables connected to the motherboard: black power cable and the red/black fan cable.

    • the black cable requires more force to remove than the other cables.

  7. DBPOWER T20 Lens Replacement: paso 7, imagen 1 de 2 DBPOWER T20 Lens Replacement: paso 7, imagen 2 de 2
    • Lift the black latch on the ZIF connector and remove the ribbon cable that attaches the digitizer to the motherboard.

  8. DBPOWER T20 Lens Replacement: paso 8, imagen 1 de 1
    • Raise motherboard by lifting sideways and then up to avoid the ports.

  9. DBPOWER T20 Lens Replacement: paso 9, imagen 1 de 2 DBPOWER T20 Lens Replacement: paso 9, imagen 2 de 2
    • Remove wires attaching the piezoelectric speakers to the motherboard.

  10. DBPOWER T20 Lens Replacement: paso 10, imagen 1 de 2 DBPOWER T20 Lens Replacement: paso 10, imagen 2 de 2
    • Remove the five screws securing the black plastic cover with a J0 screwdriver.

    • Lift up and out to remove.

  11. DBPOWER T20 Lens Replacement, Lens: paso 11, imagen 1 de 1
    • The lamp does not need to be removed for this step to be preformed.

  12. DBPOWER T20 Lens Replacement: paso 12, imagen 1 de 1
    • Detach the keystone adjuster from the lens housing.

    • Lens is on a hinge so it should lift off easily, if it doesn't, adjust by swaying it forward or backward.

  13. DBPOWER T20 Lens Replacement: paso 13, imagen 1 de 1
    • Remove the rubber foot and warranty sticker found underneath the device.

  14. DBPOWER T20 Lens Replacement: paso 14, imagen 1 de 2 DBPOWER T20 Lens Replacement: paso 14, imagen 2 de 2
    • Remove the two screws on the bottom of the device with a J0 screwdriver.

  15. DBPOWER T20 Lens Replacement: paso 15, imagen 1 de 1
    • Remove the focus-adjustment ring from the lens housing.

Conclusión

To reassemble your device, follow these instructions in reverse order.

3 personas más completaron esta guía.

Andrea Espinosa

Miembro Desde 02/15/18

506 Reputación

3 Guías creadas

Equipo

USF Tampa, Team S16-G2, Boczar Spring 2018 Miembro de USF Tampa, Team S16-G2, Boczar Spring 2018

USFT-BOCZAR-S18S16G2

5 Miembros

5 Guías creadas

3 comentarios

How does the lens parts go together?

Lay - Contestar

I need to know the same

Tremaine Mullins - Contestar

Trying to put my lens back how to install

David Williams - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 6

Ultimos 30 días: 32

Todo El Tiempo: 2,269