Introducción

A guide on how to remove the Top Cover.

  1. Turn the laptop bottom side up with the rear panel facing forward.
    • Turn the laptop bottom side up with the rear panel facing forward.

    Agregar Comentario

  2. Remove the two T8 Torx screws that secure the LED cover to the base enclosure.
    • Remove the two T8 Torx screws that secure the LED cover to the base enclosure.

    Agregar Comentario

    • Turn the laptop top side up with the front facing forward. Open the screen.

    Agregar Comentario

    • Locate the F1 and F2 keys near the top left corner of the keyboard.

    Agregar Comentario

    • While holding the F1 and F2 keys, insert a spudger between the keys into the notch in the LED cover. Lift up.

    Agregar Comentario

    • Locate the Pause and Scroll keys near the top right corner of the keyboard.

    Agregar Comentario

    • While holding the Pause and Scroll keys, insert a spudger between the keys into the notch in the LED cover. Lift up.

    Agregar Comentario

    • Insert a spudger between the F7 and F8 keys. Lift up to remove the LED cover.

    Agregar Comentario

    • Lift the back edge of the keyboard and pull towards the screen.

    Agregar Comentario

    • Pull the cable and lift up to release.

    Agregar Comentario

    • Remove the keyboard.

    Agregar Comentario

    • Locate the fan near the top left corner. It has three colored wires: yellow, red, and black.

    • Disconnect the cable connecting the fan to the system board.

    Agregar Comentario

    • Locate and remove the four screws in the copper plate.

    Agregar Comentario

    • Remove the heat spreader by pulling the whole assembly up out of the computer.

    Agregar Comentario

    • Flip the computer bottom side up with the rear facing forward.

    Agregar Comentario

    • Remove the six screws shown in picture.

    Agregar Comentario

    • Remove battery and then remove screw in metal support on case edge

    • Flip the computer top side up with the front facing you.

    Agregar Comentario

    • Lift up the palm rest from the front edge and swing it towards the screen.

    Agregar Comentario

    • Locate the first connector. Disconnect by firmly pulling up.

    Agregar Comentario

    • Locate the second connector. Remove by firmly pulling up.

    Agregar Comentario

    • Remove the palm rest.

    Agregar Comentario

    • Turn the base bottom side up.

    Agregar Comentario

    • Remove the two TM 2.5mm x 8.0mm screws that secure the top cover to the base.

    Agregar Comentario

    • Turn the base top side up with the front facing forward.

    Agregar Comentario

    • Remove the three TM 2.5 mm x 5.0 mm screws that secure the top cover to the base.

    Agregar Comentario

    • Lift the top cover straight up about one inch, then slide forward until the microphone cable is exposed.

    • Disconnect the microphone cable from the system board.

    Agregar Comentario

    • Remove the top cover from the base.

    Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Alex Hernandez

Miembro Desde 14/04/10

28 Reputación

4 Guías creadas

Equipo

Cal Poly, Team 29-74, Johann Spring 2010 Miembro de Cal Poly, Team 29-74, Johann Spring 2010

CPSU-JOHANN-S10S29G74

3 Miembros

7 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 1

Todo El Tiempo: 2,888