Saltar al contenido principal

Introducción

Parecería que es una situación común que se presenta en las cafeteras Keurig. Después de un tiempo de uso en el interior de la cafetera aparece sarro, calcificación o algún tipo de contaminación que impide que podamos preparar las 12 onzas de café para las que está diseñada. Te toma mucho más tiempo en preparar café, la cafetera se vuelve más ruidosa y preparando cuando mucho 4 onzas o menos. Esta es una guía “rápida y no documentada “ para ayudarte en la solución del problema. La cafetera Keurig utilizada en esta guía proviene de un taller en donde se usa frecuentemente y bajo condiciones que distan ser las más óptimas.

Partes

No se especificaron partes.

  1. Cafetera Keurig K40 no prepara las  12 onzas de café. Abre la tapa de la cafetera completamente para remover el sujetador de cápsulas Keurig El sujetador de cápsulas  simplemente se debe tirar hacia arriba. Puede encontrar un poco de resistencia para hacerlo debido  algunos resortes de sujeción. El sarro o calcificación es café; esto es provocado por reutilizar las cápsulas desechables que se usan sola una vez
    • Cafetera Keurig K40 no prepara las 12 onzas de café.

    • Abre la tapa de la cafetera completamente para remover el sujetador de cápsulas Keurig

    • El sujetador de cápsulas simplemente se debe tirar hacia arriba. Puede encontrar un poco de resistencia para hacerlo debido algunos resortes de sujeción. El sarro o calcificación es café; esto es provocado por reutilizar las cápsulas desechables que se usan sola una vez

    I think the first step before disassembly should be to unplug the machine FOR SAFETY!

    netdude21 - Contestar

  2. Una vez removido el inserto  para cápsulas Keurig  realize una limpieza con agua caliente tantas veces se necesite. En la parte inferior del porta cápsulas Keurig hay una pequeña aguja que perfora las cápsulas cuando insertamos una para preparar café. A un lado encontramos un pequeño orificio. Podemos utilizar un clip o algo similar para remover la suciedad, calcificación o granos de café atorados. Lo siguiente es limpiar la aguja superior. Es algo complicado debido a que es difícil de alcanzar la superficie de la aguja. Encontramos que esta aguja tiene tres orificios en el cuerpo de la misma. Abra la tapa de la cafetera completamente y utiliza de nuevo un clip o algo similar para destapar los 3 orificios y queden perfectamente limpios.
    • Una vez removido el inserto para cápsulas Keurig realize una limpieza con agua caliente tantas veces se necesite.

    • En la parte inferior del porta cápsulas Keurig hay una pequeña aguja que perfora las cápsulas cuando insertamos una para preparar café. A un lado encontramos un pequeño orificio. Podemos utilizar un clip o algo similar para remover la suciedad, calcificación o granos de café atorados.

    • Lo siguiente es limpiar la aguja superior. Es algo complicado debido a que es difícil de alcanzar la superficie de la aguja. Encontramos que esta aguja tiene tres orificios en el cuerpo de la misma. Abra la tapa de la cafetera completamente y utiliza de nuevo un clip o algo similar para destapar los 3 orificios y queden perfectamente limpios.

    I recommend using a pipe cleaner. Slide it in and out to ream the passage. Discoloration provides evidence of progress.

    Jim Cahir - Contestar

    The plastic insert shown in the first photo easily separates into two pieces, giving direct access to the bottom end of the needle .

    Tom Sager - Contestar

    Lay the unit on its side. There is a rubber fitting around the upper needle you can easily remove and clean. Use a q-tip to clean on and around the needle.

    Dave Behre - Contestar

  3. También puede  utilizar una aguja hipodermica o similar para limpiar la aguja o salida superior de agua. Para remover el tanque o depósito de agua simplemente levántelo  hacia arriba. En el fondo del tanque o depósito de agua se encuentra una válvula check ( o sin retorno) que te permite retirar  dicho depósito sin riesgo de derrame de agua. Vacíe completamente el tanque o depósito de agua
    • También puede utilizar una aguja hipodermica o similar para limpiar la aguja o salida superior de agua.

    • Para remover el tanque o depósito de agua simplemente levántelo hacia arriba.

    • En el fondo del tanque o depósito de agua se encuentra una válvula check ( o sin retorno) que te permite retirar dicho depósito sin riesgo de derrame de agua. Vacíe completamente el tanque o depósito de agua

  4. En el interior de dicha válvula se encuentra un malla pequeña que hace la función de filtro. Puedes removerlo destornillando los tres tornillos con un destornillador Phillips largo #2. Limpia la malla con agua limpia  y un cepillo. Reensambla la valvula después de haber limpiado perfectamente el filtro. El siguiente paso es remover la tapa superior de la cafetera para tener acceso a la entrada de agua del porta cápsulas. Para eso hay que remover los dos tornillos Phillips que la aseguran en su lugar. Levanta la tapa súper  y tira de ella  para removerla de su lugar.
    • En el interior de dicha válvula se encuentra un malla pequeña que hace la función de filtro. Puedes removerlo destornillando los tres tornillos con un destornillador Phillips largo #2. Limpia la malla con agua limpia y un cepillo. Reensambla la valvula después de haber limpiado perfectamente el filtro.

    • El siguiente paso es remover la tapa superior de la cafetera para tener acceso a la entrada de agua del porta cápsulas. Para eso hay que remover los dos tornillos Phillips que la aseguran en su lugar.

    • Levanta la tapa súper y tira de ella para removerla de su lugar.

    This step..."Next step is to remove the top cover to get to the water supply to the K-cup. Open the Keurig. remove two Phillips screws that hold it in place."

    Where are these screws?? Need picture of this

    cashnic72 - Contestar

    cashnic72 step 4 second image has them outlined....

    oldturkey03 -

    They're circled in the middle picture.

    David Baldon - Contestar

    After removing the screws, it was a little difficult to get the top off. Had to wiggle it around a bit and move the arm up and down to get it off

    Rich Sigle - Contestar

    Impossible to get the the top back on and functioning properly. I had to leave it just propped there without the screws back in place. Otherwise this page was extremely helpful in fixing my Keurig water flow issue!

    Sarah Fraser - Contestar

    Was impossible to get the top back on and functioning properly. Had to leave it loose on top without putting the screws back in. Other than that, this post was extremely helpful in fixing the water flow in my Keurig. Thank you.

    Sarah Fraser - Contestar

    OMG. You're awesome!!!

    Jennifer - Contestar

    I don’t have anything that looks like pic 2, step 4.

    Kevin W Burley - Contestar

  5. El suministro de agua desde la resistencia de calefacción hacia la aguja superior del porta cápsulas se realiza mediante  una manguera conectada  a una válvula anti retorno Remuéva los  dos tornillos pequeños que sujetan la manguera de agua a la entrada de la válvula antirretorno. Desenganche  la entrada de agua del conector  localizado  arriba de la aguja del portacapsulas, solo  entra a presión .
    • El suministro de agua desde la resistencia de calefacción hacia la aguja superior del porta cápsulas se realiza mediante una manguera conectada a una válvula anti retorno

    • Remuéva los dos tornillos pequeños que sujetan la manguera de agua a la entrada de la válvula antirretorno.

    • Desenganche la entrada de agua del conector localizado arriba de la aguja del portacapsulas, solo entra a presión .

    • Remueva los cinchos de sujeción ( No necesita realizar este paso necesariamente) . Simplemente saqué la otra punta de la manguera que viene desde la bomba de agua. Necesita usar un destornillador de cabeza plana para levantar el extremo de la manguera mientras jala de ella para desacoplarla.

    Mine looks different inside

    Jaime Pretell - Contestar

    Thank you so much sir!!

    Micdelos - Contestar

    I dropped the tiny screw inside. What can i do? Can i remove the metal bottom?

    Kathy Johnson - Contestar

    Kathy Johnson tiny screw inside where;-)?

    oldturkey03 - Contestar

    Wow, thanks. My dear “Madame Keurig” had been atherosclerotic — just wall-to-wall high-stress and noisy “short cups” with no hope in sight. I had run this device for 26 months with no problem, and never installed the recommended filter that snaps down on top the water input. So I did that — and a couple weeks later, Madame started getting balky and sick — not to mention very noisy. So today thanks to this suggestion, I got a long Phillips head screwdriver and got the filter out. I tried blowing through it — it was very hard to blow through. So I washed it under running water with a tooth brush and tried blowing through it again. Night and day — there was no comparison. Air went straight through it with no resistance. I put the filter back in, and Madame immediately began to perform correctly. Happy day!

    originresearch - Contestar

    Merci!!! j’ai réussi à avoir mon café ce matin grâce a vous!!!!

    tanyaeboivin - Contestar

  6. Pruebe la válvula antiretorno, sople desde el lado conectado a la resistencia calefactora. Realize esto varias veces para limpiar los sedimentos. Puede pasar un poco de agua caliente desde el porta cápsulas hacia la válvula y agitar un poco la cafetera. Ya limpia coloqué la válvula en su lugar usando los cinchos de sujeción. Reensamble la cafetera.
    • Pruebe la válvula antiretorno, sople desde el lado conectado a la resistencia calefactora. Realize esto varias veces para limpiar los sedimentos. Puede pasar un poco de agua caliente desde el porta cápsulas hacia la válvula y agitar un poco la cafetera. Ya limpia coloqué la válvula en su lugar usando los cinchos de sujeción. Reensamble la cafetera.

    This was so awesome and fixed the problem thank you so much very clear detailed instructions

    kimbasstyle - Contestar

    Problem solved. I think it was actually the first fix of clearing out the air slot in the bottom needle that did the trick. Thanks! $179.00 saves from not buying a new machine. ;-)

    Ray - Contestar

    what if you cannot blow air into the valve? Does that mean you have a bad valve and need to replace the entire machine?

    Kristal - Contestar

    @gold0348 if you are trying it from the boiler side but cannot pass air through it, could be a stuck valve. You would not have to replace the machine but you’d have to try to find a valve. You could also try to use a small wooden pencil etc. to gently apply pressure against the valve by inserting the pencil into the boiler side opening.

    oldturkey03 - Contestar

    According to Kuerig, the machine has a lifetime warranty. That said, Normally all you need is a paperclip to clean the ports as described above. I ran a pot of vinegar through mine to remove all the scale inside but Kuerig says this normally isn’t necessary. Don’t forget to run a couple of tanks of clean water afterwards to remove the vinegar taste. They have a descaling powder mix they recommend but told me vinegar was fine too. In any case, if you can’t get it working right, just take it over to Bed Bath and Beyond and exchange it for a new one.

    stevem - Contestar

    Ours is only 2 Christmas’s old and won’t heat water, how the heck do I fix that?

    Monica Jackson -

    In taking this area apart, I think I may have damaged the hose leading to the check valve, is there a way to get that hose replaced?

    netdude21 - Contestar

Conclusión

Para reensamblar la cafetera, siga los pasos en orden inverso.

67 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

100%

¡ Oscar Trejo nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

oldturkey03

Miembro Desde 29/09/10

591,458 Reputación

102 Guías creadas

Equipo

OTS Miembro de OTS

Business

1 Miembro

129 Guías creadas

Perfect - been looking all over for a solution besides trashing the unit.

Thank you for the step by step instructions!

kellywihlm - Contestar

Awesome! didn't want to have to buy a new Keurig - worked like a charm!

cabate - Contestar

awesome thank you kindley

racinnut2001 - Contestar

Outstanding presentation. I've had my Keurig apart before. However, as I use well water and don't have the best filtration system, mine tends to clog frequently.

I will add however, that the case for, at least some Keurig coffee makers have clips holding the cover in place that can be rather difficult to release.

Bill Leach - Contestar

I should add, excellent photography!

Bill Leach - Contestar

It’s easy IF you use the MACRO function in the CAM (some don’t have it)

Jess Cast -

09/30/2016

This guide and the photos are excellent! Kudos!

However, after precisely following each step I did NOT find any debris, from the K-cup holder, thru the top puncture needle, through the working check valve. Since NO clogs there, the problem is elsewhere.

Bob McGhee - Contestar

I thought that, too, until I rinsed the cup holder under some hot water and smacked it upside down on the sink a few times. Two pretty large coffee grounds came out of somewhere when I did that. Now it works fine. Good luck!

Bucky -

Thank you for your diligence in providing this guide. My check valve was all gummed up....45 minutes later, it is making great coffee again!

paulcrustad - Contestar

Excellent...Works like a charm. My K-cup holder was the culprit.

pskepple - Contestar

I thought my old Keurig coffee maker was about to give up the ghost. It had slowed to just a trickle and wouldn't fill my cup anymore. This morning I took it apart and cleaned it, easily within 30 minutes from start to finish, using these simple step-by-step instructions with pictures. It's problem was clogged needles, top and bottom. Now it works like it's brand new again. These instructions saved me from replacing it this afternoon as I'd planned. The only expense I'm out was one paperclip and two plastic tie-ties. Not a bad deal if you ask me. Seriously, not a bad deal at all.

Bucky - Contestar

After a long hour I figured out how to fix it. I give old turkey 3 a 30 for his directions and patted my FEMALE self on the back for a job well done.

Phyllis M. Newton - Contestar

@pmnewt1 thank you Ma'am and I am glad it worked out for you.

oldturkey03 -

This is truly amazing helpful. I still can not figure out the cup trat but that's OK I guess lol at least it working better than before. Thank you so much

Sandra Decker - Contestar

My go to plan is trying to take things as part and hopefully find the issue and hopefully get it all back together.

This eliminated all the hoping and got me right through to the meat of the problem.

Thank you for this awesome guide.

Mailman - Contestar

We too were about ready to give up on our machine but gave one last internet search for a possible fix. This did the trick! Thanks so much oldturkey03...you da best!

anonymous 5519 - Contestar

Thank you very much! This worked perfectly!! :)

missjones3077 - Contestar

Thank you very much. From hot water getting pumped back to the water reservoir to clean noise free full cup of joe

William S Zelazny - Contestar

We fixed our Keurig thanks to you!

deannagotte - Contestar

Thank you so much! Worked like a charm. So glad you like to tinker oldturkey03!

thies - Contestar

I tried all steps and water started coming out, but it pauses as if it was still clogged. Won't give me a full glass.

Andre Simmons - Contestar

Omgawwwd!! My sister was going to toss her old one, or put it into her grauge sale. She gave it to me, I followed your direction to the T an I now have an awesome Keurig that preforms like new!! You are Awesome!!! Thank you, Thank you, Thank you!!

Barbara Stevens - Contestar

Had a heck of a time getting the top to come off: it did not lift up and pull forward easily. Other than that problem, the cleaning process went fine. Thk you so much for posting those instructions.. I was about ready to toss my Keurig and go back to my “Mr. Coffee” Brewer!

david milright - Contestar

Thanks for your great photos and very clear instructions. After doing all of your steps I ran an empty cycle and then the “descale” light came on. So, I ran half a gallon of vinegar through it and that worked like a champion…. for two days (total of three K-Cups) now it’s back to the same light trickle of water and the “descale” light is back on. I’ve already replaced the reservoir with a brand new on. Any idea? Could it be a bad check valve? Where can one find these parts?

Gary Bennett - Contestar

Worked great for me!— with the exception that I've had trouble getting the cover back on correctly. I'll try removing it and repositioning it again today. It is now working alright as far as brewing goes, but something is binding the cover when I open and shut it to put in a K-cup. It makes a loud snapping noise unless I press down on the back of the cover with my hand when opening or closing it. But thanks for this great “remedy “!

Preston Smith - Contestar

Did you end up getting your cover back on properly? I am having trouble with that too. Thanks!

Sarah Fraser -

If you remove the top cover. There are 2 black looking tabs inside the machine, that are across from each other. The top needs to line up with them or hook in. You can test it by closing the lid before you put the crews back in

Elaine Ketchum ell -

I'm having trouble putting my top cover too. Don't see the notches.

Maritza Del Real -

My check valve was stuck. Thank you for this tear down. With out it I couldn’t figure how to get the top off

Rich Sigle - Contestar

Before I torn the coffee maker apart I unscrewed the round filter at the bottom of the water tank and washed it out it was very slimy and had a ton of sediment. used vinegar on the unit just last month, now it is working just fine

Carol Thompson - Contestar

Perfect - been looking all over for a solution besides trashing the unit.

Thank you for the step by step instructions!

randy.pitcock - Contestar

Son. This was the exact fix. I tried it the first time and it didn’t work. Followed the steps again, and spent a bit more effort on step 5. That was precisely the issue. Thank you for taking the time to make this help. Took me ten minutes to take apart and reassemble.

Nathan Allen - Contestar

My machine was making a clicking sound like it was trying to flush water through but none was coming out. These directions worked perfectly for me. On the first try I didn’t spend enough time on step 5, and it didn’t work. But going through again and taking the time to flush the check valve did the trick.

Thank you!

Nathan Allen - Contestar

I cleared the check valve as instructed and I still have water coming out of the side instead of the top any thoughts

Kathy Blake - Contestar

As instructed I clean the check valve and the needles and the screen reassembled and I still have water coming out of the side valve any thoughts

Kathy Blake - Contestar

Thank you, Thank you and Thank you! I ran the gym clip up inside the needle and it worked perfectly, you just saves me $100! Thank you so much!!!

Kelly Johnson - Contestar

Thank you, Thank you and Thank You! I ran a bent gym clip up inside the needle and it worked perfectly. You just saved me $100. THANK YOU!!!

Kelly Johnson - Contestar

Thank you thank you!! Worked perfect!

suth_h - Contestar

How to get the Phillip screws out! They are stuck

SHIRLEY Ann parish - Contestar

@keurig123 stuck how and where?

oldturkey03 -

Thank you so much!!!! Life saver

Micdelos - Contestar

Where are the screws to remove the top cover?

pboser - Contestar

Step 4. Picture 2. Underneath the top cover

Elaine Ketchum ell -

Mine brews about 8 oz, very slowly. tried descaling , cleaning needles, lines, check valve , cup holder, screen filter and new filter.

Still only 8 oz. I’ll brew a cup tomorrow to see if it comes out faster. May just have to accept 8oz cups

Elaine Ketchum ell - Contestar

@elliek don’t forget the little filter inside the reservoir in step #4. You’ll be amazed by the things this little bugger can cause if it is clogged.

oldturkey03 -

I am having trouble getting the top to fit right. I’ve tightened the front screws but the back part of the top is preventing it from closing fully. Any thoughts?

Stormy Weather - Contestar

In this case, the upper check valve was the problem - it was sticking. One giveaway was that blowing into the overflow return to the reservoir with a soda straw, gave bubbles out the lower reservoir (check valve) connection and this temporarily cleared the sticking upper check valve. After a while, it would begin sticking again and the excess hot water was returned to the reservoir.

I found that a plastic soda straw was the right diameter to mate with the upper check valve, which in turn mates with off the shelf (home Depot) plastic tubing. That way, hot water could flow right through. and it took several minutes to clean out the residue inside. My version was the Kitchenaid that had the reservoir screen in the removable filter holder - no need to remove the check valve to get the screen. The Kitchenaid has a paper charcoal filter that has to be replaced periodically instead.

Chester Heath - Contestar

I would like to add one other thing that I found on one of my Keurig units. When you remove the water reservoir look into the hole under the reservoir where the water flows into the unit ( you may need a bright light ). You should see black plastic with checker pattern holes. My unit had build up which was narrowing the square holes off ( vinegar flush through unit had not removed this scale ) . I mechanically cleaned each little hole with a pointed toothpick and laid the unit on its side at the sink and flushed out the residue with the sink spray nozzle. This solved solved my problem of slow water draw down in the reservoir at the start of the brew cycle. It was taking twice as long to get water into the system before the brew cycle would start. This might stress the internal pump and cause premature failures . Guess that’s why they came out with the new 2.0 version which appears to use some type of plunger pump for the water which gives that clickety-click sound when brewing.

Robert Perkins - Contestar

Thank you! Keurig works! Very simple and clear instructions!!!

Deann Kirby - Contestar

Fantastic instructions and photos! Our check valve was stuck. Saved us from buying a new one. Thanks!!

S G Turner - Contestar

Thank you!

Suggestion, on step 2, you should show a picture of the disassembled cup holder. I was not aware it comes apart until I used a paperclip to clean the pin hole and observed that the paper clip went into the bottom of the holder. It makes it easier to clean if you pop off the bottom “cap” of the holder.

josephy - Contestar

I got quite the surprise this morning when I lifted out yesterday's Kcup and a bug crawled out and then crawled into the machine. I ran 2 tanks of vinegar through but paranoid there is a bug body in there. Do you think i'll be able to see enough of the inner workings by following your guide? I got takeout coffee this morning and bought a $9.00 5-cup coffeemaker as a backup. I love my Keurig and hope I can restore it!

Missy - Contestar

@mamapeep Whatever bug crawled out of the Keurig is most likely long gone. It just liked the leftover K-cup. Since you already cleaned the “plumbing” of the Keurig I am pretty sure it is not anywhere near your water supply.

oldturkey03 -

Have an old 2011 Platinum B70 that quit pumping the water. I put vinegar in the water holder and let it sit for 24 hrs and still would not work. So that is why I found this site. I was hoping the vinegar would loosen things up but still would not pump water. So I picked it up off the floor about 6 in. and gently let it drop down on the floor. I did this 3 times. Sure enough I must have jared something loose and it began to pump. Then I descaled it with 48 oz of white vinegar according to directions (let it sit 4 hrs when add water light comes on) after you run the vinegar through before you rinse with clear water. Works like brand new. Had one other problem in past that I can tell you about. The on/off switch would jam and was so tight I could not turn it on. Called Keurig and they said it could not be fixed and offered me a discount on new one. Well, I decided I would spray WD-40 on the switch. I laid the machine on its side so WD-40 could run inside. Yes, that worked.

Barbara Othon - Contestar

This worked perfect! I still can’t get the top to fit on right, but everything else works like new. The steps and the pictures were very clear and easy to understand. Thank you!

Kristie Layne - Contestar

I tried and I tried these steps to no avail. I spent FAR TOO MUCH time repeating Step 6. Before replacing the cover, I watched my machine try to brew. I think it’s toast. I’ve had my Keurig for 6.5 years. When it tries to brew it spurts out a little water & then no water even moves up the hoses out of the pump.

starfirelite79 - Contestar

Meanwhile, since I cleaned the water tank filter, it’s happily bubbling away. I need my morning cup of coffee. I have not had it yet today. I’m ready to throw my Keurig against a brick wall.

starfirelite79 - Contestar

Our keurig showing not ready and won’t turn off and no lights in the reservoir. Think the magnet does not contact

Norma - Contestar

Makes Mr. Coffee look better all the time!

gimmeadeal - Contestar

WOW! After all the searches glad I found this one! Had 2 clogged hoses at the needle area and the hopper area, eventhough I descaled it a cpl months ago, I had no idea you could even take it apart like this. It was easy took me 20 mins, cleared hoses, descaled again and the water is flowing like a river…..brand new again!!!!

Thanks

Bruce - Contestar

Great, easy to follow steps, and a wonderfully clean Keurig!!!

Thank

Mel Fischer - Contestar

Perfect! I descaled and big chunks of limescale got into the lines. If everyone tried to repair their appliances instead of ditching and buying new we wouldn’t be as disposable of a society!

Michele B - Contestar

Thank you! It all worked

audreyberner - Contestar

Perfect guide. Thanks so much. Was ready to throw it away, but now it works great again.

Stephen Post - Contestar

When I shoved the paperclip up the needles to see if they were plugged, which they weren’t I took the top off and noticed that there was little holes in the tubing.Must have been from shoving the paperclip up inside.Though many people said no harm can be done. Now how do I fix the little holes? Glue?

flyingcyberdog - Contestar

Have a B40 Kuerig coffee maker that was slowing done a lot while brewing and delivering half as much coffee it should. Only snag was having to buy a long shank phillips driver. (Depth of water tank is is 10 inches) Problem completely cured and works like new.

glenharts - Contestar

KEurig K200 disassemble and reassemble super easy

https://youtu.be/BuKrGVtH7PU

rosanne623 - Contestar

Do these instructions help with the 2.0 models? I’m not afraid to tear something apart, but I am a little worried about the electronics and the touch screen. My brewer is only about a year or two old, (I bought it used from a friend). I’ve cleaned it with vinegar, and the descaling solution that is $13 dollars a bottle. No luck, I’m considering trying CLR because I know I have extremely hard water and it builds up scale on everything. I started out using bottled water, but sometimes I have put my tap water in it. As soon as the hubs gets up and has his coffee, I’m going to try to clean the screen at the bottom of the tank, first. If that doesn’t work, then I’m going for the full tear down. I NEED my coffee. I’m pretty sure my water is the culprit, because it’s progressively gotten worse over the last couple months.

jenedm1978 - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 164

Últimos 7 Días: 1,088

Últimos 30 Días: 4,771

Todo El Tiempo: 300,709