Saltar al contenido principal

Limpieza de Logitech MX Master

Qué necesitas

  1. Limpieza de Logitech MX Master, La foto del antes: paso 1, imagen 1 de 1
    • ¡Eso es un montón de mugre!

  2. Limpieza de Logitech MX Master, Retirada de los pies: paso 2, imagen 1 de 2 Limpieza de Logitech MX Master, Retirada de los pies: paso 2, imagen 2 de 2
    • El ratón tiene cuatro pies en la parte inferior, pero sólo hay que quitar los dos largos. He utilizado el Jimmy del Pro Tech Toolkit.

    • No tenía pies nuevos a mano, así que tuve que reutilizar los originales. Por eso no hay ningún paso para limpiar el adhesivo y poner pies nuevos.

    It makes sense to remove them with heat. That way there is a possibility to return them back to the mouse.

    Stjepan - Contestar

  3. Limpieza de Logitech MX Master, ¡Momento de los tornillos!: paso 3, imagen 1 de 3 Limpieza de Logitech MX Master, ¡Momento de los tornillos!: paso 3, imagen 2 de 3 Limpieza de Logitech MX Master, ¡Momento de los tornillos!: paso 3, imagen 3 de 3
    • ¡Acelera esos destornilladores! La primera ola consiste en cuatro tornillos PH1 y dos T5 en la parte inferior.

    • Una vez solucionado esto, el ratón debería ser fácil de abrir.

  4. Limpieza de Logitech MX Master, Cuidado al abrirlo: paso 4, imagen 1 de 2 Limpieza de Logitech MX Master, Cuidado al abrirlo: paso 4, imagen 2 de 2
    • Al abrir el ratón ten en cuenta la posición de las pinzas para evitar consecuencias indeseadas.

    Totally unclear how exactly to open it….

    Service Tool - Contestar

  5. Limpieza de Logitech MX Master, Cables de cinta.: paso 5, imagen 1 de 1
    • Abre el conector con la herramienta que mejor te funcione, a menos que seas como yo y hayas sacado accidentalmente el cable del conector en el paso anterior.

    Well, THAT BROKE. Any advice on how to keep it in without the connector?

    Andrei Pierre - Contestar

    Which part broke?

    Skylar - Contestar

    How do I re-attach the ribbon cable?

    Peter Szabo - Contestar

    any chance you guys know where to buy the ribbon cable and the lock?

    Chino Mercado - Contestar

    to release the ribbon, the white bit flaps upwards

    Adam Sherwood - Contestar

  6. Limpieza de Logitech MX Master, Mitad inferior: paso 6, imagen 1 de 3 Limpieza de Logitech MX Master, Mitad inferior: paso 6, imagen 2 de 3 Limpieza de Logitech MX Master, Mitad inferior: paso 6, imagen 3 de 3
    • Esta es la parte en la que me doy cuenta de que necesito una mejor iluminación.

    • Deje la mitad superior a un lado por ahora. La extracción de la batería consiste en tres tornillos PH1 y un conector que realmente no quiere soltarse.

  7. Limpieza de Logitech MX Master, Mitad inferior (continuación): paso 7, imagen 1 de 3 Limpieza de Logitech MX Master, Mitad inferior (continuación): paso 7, imagen 2 de 3 Limpieza de Logitech MX Master, Mitad inferior (continuación): paso 7, imagen 3 de 3
    • ¡Es hora de cambiar un poco! La PCB que aloja los interruptores para los clics izquierdo y derecho se desprende con cuatro tornillos P0 y otro conector ZIF.

    • El conjunto de la rueda de desplazamiento se sujeta con dos tornillos P0 en la parte delantera. También hay un conector para el motor escondido bajo el cable plano de la PCB que acabas de quitar.

    • Estos tornillos no son visibles en este paso, pero se pueden ver en el anterior. Soy terrible para tomar fotos.

    • En la última foto se pueden ver algunos de los restos que causan mis problemas de desplazamiento.

  8. Limpieza de Logitech MX Master, PCB inferior: paso 8, imagen 1 de 2 Limpieza de Logitech MX Master, PCB inferior: paso 8, imagen 2 de 2
    • Otros tres tornillos P0 mantienen este en su lugar.

    • Ten cuidado de volver a poner la pequeña chuchería en el cable rojo en su sitio (no recuerdo el nombre)

    • Podemos ver el conector micro USB en la parte inferior. Por desgracia, no puedo actualizarlo a USB-C con el equipo que tengo.

    • Sin embargo, ¡tengo el equipo para limpiarlo! Una lata de aire comprimido era todo lo que necesitaba.

  9. Limpieza de Logitech MX Master, Rueda del ratón: paso 9, imagen 1 de 3 Limpieza de Logitech MX Master, Rueda del ratón: paso 9, imagen 2 de 3 Limpieza de Logitech MX Master, Rueda del ratón: paso 9, imagen 3 de 3
    • No pude sacar la rueda del conjunto, pero pude hacerla girar con un poco de aire comprimido. No lo grabé en vídeo, pero salió volando un gran trozo de polvo.

    • Me disculpo de antemano por haber filmado en modo retrato. Además, no conseguí fotografiar los restos del interior de la rueda.

    • Ese resorte en la parte inferior en la primera imagen probablemente se caerá. Asegúrese de no perderlo de vista.

    • He desmontado el conjunto para intentar sacar la rueda, pero no lo he conseguido. No sé dónde va este muelle de forma extraña, posiblemente en esta clavija, pero lo dejé fuera y no parece ser importante.

    I had jam stuck in the casing of the wheel, but the pins of the wheel are firm in place and you can’t remove it from that transparent casing. So I removed the trigger that activates the ratcheting feature. You have to remove the screw that is in the casing. That holds the trigger in place. Then disconnect the spring from the center of the case and slide out the trigger. Then I brought a galss of hot water and dipped the casing and wheel inside and with an end of a zip tie (that is very thin and at the same time very firm and also will not scratch the metal part of the wheel) I esealy removed the dust and jam that was jamming the spin of my wheel and used a tissue to dry the assembaly as I cleaned. Be careful not to get the motor wet though. You can remove the motor and just dip the whole thing in. I also poped out the pin halfway from one side of the wheel by pulling the casing apart a little to make easier access. Be careful not break the casing with too much pressure as that will be it for your MX Master!

    hamidreza saleh - Contestar

    I was able to remove the wheel with a butter knife, I forced out the pin on the side opposite the ratchet jammed my finger in a way to stop it slipping, then pried the knife in the other side and levered the other side away. It made a bit of a scary noise but nothing broke. I got it bck in my sitting the wheel holder on a flat surface, pushed down, and pried the plastic apart on the ratchet side with the knife, and it popped in all at once. As a warning though, the friction of the scroll wheel appears to have increased, it no longer scrolls for forever, but just a few seconds when given a hard flick. I was only game enough to try getting the wheel out cos I recently got the MX Master 3 cos the tracking stopped working on my MX Master (It worked again as soon as I opened it though)

    Ethan Corney - Contestar

    I can confirm that what Ethan said works. Basically you need to push the left side of the wheel (side without the blades) out first and then stick the knife in on the other side and turn a little bit.

    Jonathan Tsoi -

    Übt diese Feder möglicherweise Druck auf die Innenseite des Mausrades aus und sorgt dann mit im Mausrad befindlichen Nocken zusammen für die Raste-Funktion?

    Niklas - Contestar

    I'm going crazy with that "oddly shaped spring"! Does anyone knows how to put it back in place???

    Joao Alberto Gazzinelli - Contestar

    Joao, it should be on the top of the motor (servo), about 5mm from the black, halfmoon-shaped moving part.

    Logi logi -

  10. Limpieza de Logitech MX Master, ¡Casi terminado!: paso 10, imagen 1 de 2 Limpieza de Logitech MX Master, ¡Casi terminado!: paso 10, imagen 2 de 2
    • Puedes seguir los pasos 5-8 a la inversa para volver a montar el fondo.

    • La parte superior sólo necesita un poco de aire comprimido, no es necesario desmontarla.

    • Puedes pulsar los botones hacia abajo para acceder más fácilmente a los restos.

  11. Limpieza de Logitech MX Master, Enhorabuena, ¡lo has conseguido!: paso 11, imagen 1 de 1
    • Después de seguir los pasos 1 a 4 a la inversa, el ratón vuelve a estar limpio. Y probablemente más limpio que el mío.

Conclusión

¿Insertar la conclusión aquí?

33 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

en es

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Skylar

Miembro Desde 01/22/15

1,091 Reputación

1 Guía escrita

Equipo

Donut Miembro de Donut

Business

1 Miembro

5 Guías creadas

14 comentarios

I followed your guide and I found a problem when I put everything together again. Now I turn on the mouse and it’s broken. The battery leds just blink and it doesn’t respond to pressing the channel selection or connect buttons, it just doesn’t work or sincronizes with the dongle, just shows the battery leds blinking. Anyone has any suggestion? Many thanks.

Juan Suarez - Contestar

I have the same problem (all three LED’s blink green and no response to pressing channel selection or connect buttons) that Juan Suarez describes.

I would also be happy for any suggestions on how to fix the issue.

Max -

And? Did you find a way to fix it?

Nicholas Blair -

Unfortunately I did not.

Max -

Have you tried reseating the ribbon cables?

Skylar -

I have just now.

Is it not just the one ribbon cable (see step 5)?

Max -

Reseating the ribbon cables fixed that for me. There is a blue line on the cables. That has to align perfectly to the edge of the cable lock when down and fixed.

mark -

I would recommend applying heat to the feet before removing them. I damaged one. Used heat and the second one came off and went back on perfectly.

charlie - Contestar

This is something I recommend as well since I now do not have the feet back. I removed them with a scalpel and the adhesive is now missing. I think it makes sense to apply heat (hair heater) and just remove them and put back on.

Stjepan -

My scroll wheel stopped responding to input. After cleaning out all the lint from the scroll wheel I still has issues. I cleaned off the boards and wiped down the mouse wheel sensor and ir emitter. Tested it out and it’s working again.

David Johnson - Contestar

I’ve had my MX Master for 7 years now and the thumb button broke (got stuck pressed, so the special feature was always active and the cursor didn’t move). With the help of these instructions, I was able to cut the wires to the button to make the mouse usable again. Lost 1 feature but glad to keep the same mouse, hopefully I’ll get another few years out of it!

Tucker Martin - Contestar

When you are "in there" anyways, you might consider gluing the the plastic thing on the motor axle with cyanoacrylat. This part working it self up is the typical cause of the wheel click function dying! ;-)

Anders Frederiksen - Contestar

I also ended up with a loose spring... I'm pretty sure it goes here: Spring-placement... (Skylar, you are welcome to include the picture!)

Cheers!

Anders Frederiksen - Contestar

By the way: I recommend leaving the center part of the low friction pads in place. I've had mine disassembled three (!) times now because of the failing scroll wheel click - and the original pads are still OK (with no additional glue added)...

PS: Annoying the Logitech designers did not leave the screws immediately accessible - especially when they messed up in production (the plastic part on the motor - hopefully the cyanoacrylate means I'm done opening it for that!)

Anders Frederiksen - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 47

Ultimos 7 días: 281

Ultimos 30 días: 1,341

Todo El Tiempo: 89,221