Partes

No se requieren partes.

Remove the four screws on the side of the speaker.
  • Remove the four screws on the side of the speaker.

Agregar Comentario

Remove the two back screws on the bottom of the camera.
  • Remove the two back screws on the bottom of the camera.

  • Note: Bottom screws are longer than the top ones, so label accordingly for easy reassembly.

Agregar Comentario

Remove the four screws on the side opposite of the speaker.
  • Remove the four screws on the side opposite of the speaker.

Agregar Comentario

Once all screws have been removed, gently pry open bottom casing. With tweezers, carefully remove ribbon from LCD screen.
  • Once all screws have been removed, gently pry open bottom casing.

  • With tweezers, carefully remove ribbon from LCD screen.

  • Set bottom casing aside.

Agregar Comentario

Gently pry apart the top casing using tweezers. Set the top casing aside. Set the top casing aside.
  • Gently pry apart the top casing using tweezers.

  • Set the top casing aside.

Agregar Comentario

Use tweezers or prongs to pry the LCD screen off from the opening. Note: The bottom of the LCD screen is attached to the frame by a few pieces of black tape.
  • Use tweezers or prongs to pry the LCD screen off from the opening.

  • Note: The bottom of the LCD screen is attached to the frame by a few pieces of black tape.

Agregar Comentario

Lift up the LCD screen, slowly move it to the other side. Lift up the LCD screen, slowly move it to the other side.
  • Lift up the LCD screen, slowly move it to the other side.

Agregar Comentario

Pry off the LCD casing. Pry off the LCD casing.
  • Pry off the LCD casing.

Agregar Comentario

Flip open the connector holding the ribbon. Pull out the LCD screen with the ribbon from the camera. Pull out the LCD screen with the ribbon from the camera.
  • Flip open the connector holding the ribbon.

  • Pull out the LCD screen with the ribbon from the camera.

Agregar Comentario

Remove two screws on the side where the battery is located. Remove the lanyard loop after the screws come off.
  • Remove two screws on the side where the battery is located.

  • Remove the lanyard loop after the screws come off.

  • Slowly pull the side casing so it becomes dislocated from the top of the camera frame.

Agregar Comentario

On the front of the camera near the flash flip the connector holding the ribbon. Remove the ribbon from the connector.
  • On the front of the camera near the flash flip the connector holding the ribbon.

  • Remove the ribbon from the connector.

Agregar Comentario

Carefully remove the L shaped frame from the camera. At the bottom of the camera the L shaped frame is being held in by two plastic bumps and a metal tab. Pop the frame off the bumps and tabs.
  • Carefully remove the L shaped frame from the camera.

  • At the bottom of the camera the L shaped frame is being held in by two plastic bumps and a metal tab.

  • Pop the frame off the bumps and tabs.

  • Note: There is a yellow and orange wire soldered onto the camera. Be careful not to pull them off.

Agregar Comentario

This is the flash assembly. It needs to be removed with soldering points circled.
  • This is the flash assembly.

  • It needs to be removed with soldering points circled.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Christian

Miembro Desde 28/01/11

320 Reputación

3 Guías creadas

Equipo

Cal Poly, Team 4-38, Regan Winter 2011 Miembro de Cal Poly, Team 4-38, Regan Winter 2011

CPSU-REGAN-W11S4G38

4 Miembros

7 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 1

Últimos 30 Días: 3

Todo El Tiempo: 2,446