Repara tus cosas Comunidad Tienda

Canon PowerShot SX260 HS LCD Screen Replacement

Introducción

If you need to replace your LCD Screen on your Canon PowerShot SX260 HS this guide is for you!

Qué necesitas

  1. Canon PowerShot SX260 HS LCD Screen Replacement, LCD Screen: paso 1, imagen 1 de 3 Canon PowerShot SX260 HS LCD Screen Replacement, LCD Screen: paso 1, imagen 2 de 3 Canon PowerShot SX260 HS LCD Screen Replacement, LCD Screen: paso 1, imagen 3 de 3

    • Be sure to always remove the battery from the camera before disassembling to avoid permanent damage.

    • The camera has a total of 6 (3 mm) external screws that will need to be removed; 2 on the left side, 2 on the bottom, and 2 on the right side.

    • Remove the 2 (3 mm) screws on the left side

    • Remove the 2 (3 mm) screws on the bottom of the camera.

    • Remove the 2 (3 mm) screws on the right side of the camera.

    Editar

  2. Canon PowerShot SX260 HS LCD Screen Replacement: paso 2, imagen 1 de 1

    • Use your plastic opening tool to gently lift and remove back face plate.

    • Unplug the ribbon cable leading to the mode dial.

    Editar

  3. Canon PowerShot SX260 HS LCD Screen Replacement: paso 3, imagen 1 de 1

    • After removing exterior screws, gently lift off the front face plate with your fingers.

    Editar

  5. Canon PowerShot SX260 HS LCD Screen Replacement: paso 4, imagen 1 de 1

    • Remove the 4 (3 mm) screws that are under the face plate.

    Editar

  6. Canon PowerShot SX260 HS LCD Screen Replacement: paso 5, imagen 1 de 1

    • Next, remove the 2 (3 mm) interior screws on the left side of the camera.

    Editar

  7. Canon PowerShot SX260 HS LCD Screen Replacement: paso 6, imagen 1 de 1

    • After removing the interior left screws, use a plastic opening tool to gently pull the top face plate off.

    Editar

  8. Canon PowerShot SX260 HS LCD Screen Replacement: paso 7, imagen 1 de 1

    • Next,take off the 2 (3mm) screws on the back side of the camera to remove the dial panel.

    • Gently lift the panel with your fingers.

    • Be careful not to rip the attached yellow ribbon cable.

    Editar

  9. Canon PowerShot SX260 HS LCD Screen Replacement: paso 8, imagen 1 de 1
    Herramienta utilizada en este paso:
    Tweezers
    $4.99
    Comprar

    • Carefully unplug the yellow ribbon cable from the front of the camera using your tweezers.

    Editar

  10. Canon PowerShot SX260 HS LCD Screen Replacement: paso 9, imagen 1 de 1

    • Gently slide the LCD screen to the right and remove.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

3 personas más completaron esta guía.

Autor

con 4 otros colaboradores

Tyler Kelch

Miembro Desde 03/05/15

622 Reputación

4 Guías creadas

Insignias: 8

+ 5 más insignias

Equipo

Sam Houston State, Team 11-8, Blackburne Winter 2015 Miembro de Sam Houston State, Team 11-8, Blackburne Winter 2015

SHSU-BLACKBURNE-W15S11G8

Miembros de 2

4 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 5

Ultimos 7 días: 43

Ultimos 30 días: 123

Todo El Tiempo: 4,066