Repara tus cosas Comunidad Tienda

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

Canon PowerShot A590 IS LCD screen Replacement

Introducción

First you will remove the batteries and back cover of the camera. You will unscrew the LCD. You will then remove the ribbon attached to the logic board. Finally you will unsolder the LCD from the logic board.

Qué necesitas

  1. Canon PowerShot A590 IS LCD screen Replacement, Batteries: paso 1, imagen 1 de 2 Canon PowerShot A590 IS LCD screen Replacement, Batteries: paso 1, imagen 2 de 2

    • The battery hatch is on the bottom of the camera.

    • CAUTION: Locate the switch to open the hatch and push gently toward the front of the camera. Too much force can break the hatch.

    • While the switch is pushed forward, pull the cover away from the camera.

    Traducir

  2. Canon PowerShot A590 IS LCD screen Replacement: paso 2, imagen 1 de 1

    • This camera requires AA batteries.

    • To remove batteries, simply allow them to fall out of the camera.

    • Use a fingernail to lift the clock battery out of the camera.

    Traducir

  3. Canon PowerShot A590 IS LCD screen Replacement: paso 3, imagen 1 de 1

    • When replacing the AA batteries, verify they are oriented correctly by following the (+) and (-) signs on the camera.

    Traducir

  4. Canon PowerShot A590 IS LCD screen Replacement, Back Cover: paso 4, imagen 1 de 1

    • Remove the screw located under the rubber flap on the left side of the camera using a Phillips #00 screwdriver.

    Traducir

  6. Canon PowerShot A590 IS LCD screen Replacement: paso 5, imagen 1 de 1

    • Remove the two screws located on the other side of the camera using a Phillips #00 screwdriver.

    Traducir

  7. Canon PowerShot A590 IS LCD screen Replacement: paso 6, imagen 1 de 1

    • Remove the three screws located at the bottom of the camera using a Phillips #00 screwdriver.

    Traducir

  8. Canon PowerShot A590 IS LCD screen Replacement: paso 7, imagen 1 de 1

    • Open the battery cover.

    • Using the iFixit opening tool, push up gently around all edges of the camera.

    Traducir

  9. Canon PowerShot A590 IS LCD screen Replacement, Remove LCD Screws: paso 8, imagen 1 de 1

    • Remove the four (4) screws near the corners of the LCD.

    Traducir

  10. Canon PowerShot A590 IS LCD screen Replacement, Lift LCD Screen: paso 9, imagen 1 de 1

    • CAUTION: The LCD is connected to the logic board with different wires and a ribbon. Using too much force may disconnect these parts.

    • Lift the screen off of the logic board.

    Traducir

  11. Canon PowerShot A590 IS LCD screen Replacement, Remove Ribbon: paso 10, imagen 1 de 1

    • With the LCD pulled back in one hand and using a blue iPod opener tool, pull the black retaining clip up and remove the ribbon.

    Traducir

  12. Canon PowerShot A590 IS LCD screen Replacement, Unsolder LCD: paso 11, imagen 1 de 1

    • Use tweezers to unsolder the wires from the bottom left corner on the back of the LCD.

    • Remove the solder from the wires.

    Traducir

  13. Canon PowerShot A590 IS LCD screen Replacement: paso 12, imagen 1 de 1

    • The LCD is now free from the camera and you are now able to replace it with the new screen.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Autor

con 12 otros colaboradores

Zach

Miembro Desde 10/11/10

281 Reputación

6 Guías creadas

Insignias: 12

+ 9 más insignias

Equipo

Cal Poly, Team 9-19, Regan Fall 2010 Miembro de Cal Poly, Team 9-19, Regan Fall 2010

CPSU-REGAN-F10S9G19

4 Miembros

14 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 1

Ultimos 30 días: 8

Todo El Tiempo: 9,659