Introducción

Use this guide to replace or repair your speaker.

Partes

No se requieren partes.

  1. Orient the camera so that the viewfinder is on your left and the lens is on your right.
    • Orient the camera so that the viewfinder is on your left and the lens is on your right.

    • Remove the 4mm #00 Phillips screw.

    Agregar Comentario

  2. Reorient the camera with the back button pad and viewfinder towards you.
    • Reorient the camera with the back button pad and viewfinder towards you.

    • Remove the three 4mm #00 Phillips screws shown on the rear face of camcorder.

    Agregar Comentario

    • Remove the plastic cover from the rear of the camcorder by gently pulling it towards you while holding the camera as shown.

    • The Battery Should be removed at this point, please ignore it in the picture.

    Agregar Comentario

    • Remove the 4mm #00 Phillips screw located to the right of the LCD release switch.

    Agregar Comentario

    • Open the LCD by using the release switch.

    • Reorient the camera with the playback button pad and edge of LCD screen facing you.

    • Remove the 4mm #00 Phillips screw shown.

    Agregar Comentario

    • Reorient the camera with the top facing you. The side with the LCD screen should be on the right and the other side panel should be on the right.

    • Open the pop up flash on the top of the camcorder.

    • A loud clicking noise is expected.

    • Remove the 4mm #00 Phillips screw shown.

    Agregar Comentario

    • Reorient the camera with the bottom facing you, LCD screen on the right, side panel on the left.

    • Open the tape deck by sliding the switch and moving the deck cover to the left as shown.

    Agregar Comentario

    • Remove 4mm #00 Phillips screw.

    Agregar Comentario

  3. Reparte el espíritu de reparación esta Navidad
    Obtén $12 de descuento en tu compra de $50 o más con el código FIXMAS12
    Reparte el espíritu de reparación esta Navidad
    Obtén $12 de descuento en tu compra de $50 o más con el código FIXMAS12
    • Reorient camera with lens facing you.

    • Remove the #00 Philips 4mm screw shown on the hinge of the tape deck cover.

    Agregar Comentario

    • To remove the camcorder lens hood, twist the hood to counterclockwise and it will come loose, then pull towards you.

    Agregar Comentario

    • Close the tape deck by gently pushing it toward the body of the camera.

    • Slide and remove the plastic cover on the bottom right, exposing the interface shown.

    Agregar Comentario

    • Gently pull the front plastic cover towards you to remove.

    Agregar Comentario

    • Remove 2 Philips #00 4mm screw shown.

    Agregar Comentario

    • Reorient the camera so you are looking at the side of the camera with the viewfinder on the left and lens on the right.

    • Holding the camera as shown,remove the 4mm #00 Phillips screw.

    Agregar Comentario

    • Remove the 4 Philips #00 4mm screws shown.

    Agregar Comentario

    • Reorient the camera with the lens facing you.

    • Gently pull the side panel of the camera to the right to remove.

    • Be aware that that there are wires connecting the cover to the body of the device, so the side cover will not come off entirely.

    Agregar Comentario

    • The side of the device should now be open as shown. Again, there are wire connections between the side cover and the body of the camcorder. Do not separate the two entirely!

    Agregar Comentario

    • Remove the screw above the speaker's housing.

    Agregar Comentario

    • Remove the small battery with the "Caution" on it.

    Agregar Comentario

    • Remove the screw from inside the battery housing.

    Agregar Comentario

    • Remove the 3 screws holding the metal piece over the speaker.

    Agregar Comentario

    • Lift up and remove the metal cover.

    Agregar Comentario

    • Lift and remove the speaker.

    Agregar Comentario

    • Replace the broken speaker with a new one.

    • The speaker's wires need to be desoldered.

    Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Equipo

Cal Poly, Team 1-12, Amido Winter 2011 Miembro de Cal Poly, Team 1-12, Amido Winter 2011

CPSU-AMIDO-W11S1G12

4 Miembros

6 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 1

Todo El Tiempo: 592