Menú

Tus configuraciones

Mi Mesa de Trabajo

Obtén acceso rápido a guías, partes y respuestas para tus dispositivos
Mi Carrito

Al parecer tu carrito está vacío

Visita Nuestra Tienda

Canon EOS 300 Bottom Panel Replacement

Escrito Por: Tammy Kong (y 3 de otros participantes)
  • Comentarios: 0
  • Favoritos: 0

Dificultad

Fácil

Pasos

10

Tiempo Requerido

10 minutos

Secciones

4

Banderas

0

Introducción

The bottom panel can be easily removed, and allows access for replacement on other parts of the camera.

Herramientas

Comprar estas herramientas

Partes

No se especificaron partes.

  1. Open up the battery door. Open up the battery door. Open up the battery door.

    • Open up the battery door.

    Editar

  2. Remove the batteries from the camera by sliding them out into your palm. Remove the batteries from the camera by sliding them out into your palm.

    • Remove the batteries from the camera by sliding them out into your palm.

    Editar

  3. Release the side latch to open the back panel. Release the side latch to open the back panel.

    • Release the side latch to open the back panel.

    Editar

  4. Remove the two black 4.5mm screws above and below the latch. Remove the two black 4.5mm screws above and below the latch.

    • Remove the two black 4.5mm screws above and below the latch.

    Editar

  5. Kits de Reparación de Batería de iPhone

    Sólo $29.99

    Buy Now

    Kits de Reparación de Batería de iPhone

    Sólo $29.99

    Buy Now

  6. Using your finger, carefully pry open the side panel from the top of camera. Pull panel downwards to remove.

    • Using your finger, carefully pry open the side panel from the top of camera.

    • Pull panel downwards to remove.

    • Make sure to keep track of the small black piece of rubber under the latch.

    Editar

  7. Remove the two silver 6mm Phillips #1 screws. Remove the two silver 6mm Phillips #1 screws.

    • Remove the two silver 6mm Phillips #1 screws.

    Editar

  8. Flip camera over to the bottom. Remove the one 5mm Phillips #1 silver screw.

    • Flip camera over to the bottom.

    • Remove the one 5mm Phillips #1 silver screw.

    Editar

  9. Remove the front panel by pulling away from the side with the lever. Remove the front panel by pulling away from the side with the lever.

    • Remove the front panel by pulling away from the side with the lever.

    Editar

  10. Remove three black 7.3mm Phillips #1 screws located on the corners of the camera. Remove five black 4.8mm Phillips #1 screws.

    • Remove three black 7.3mm Phillips #1 screws located on the corners of the camera.

    • Remove five black 4.8mm Phillips #1 screws.

    Editar

  11. Simply remove the bottom panel by prying it off with your finger. When removing the panel, be sure the bottom of the camera is facing upright. There are loose gears that may fall out. Be wary of a loose piece of foam attached to the bottom panel.

    • Simply remove the bottom panel by prying it off with your finger.

    • When removing the panel, be sure the bottom of the camera is facing upright. There are loose gears that may fall out.

    • Be wary of a loose piece of foam attached to the bottom panel.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 3 otros colaboradores

Tammy Kong

Miembro Desde 23/01/14

643 Reputación

6 Guías creadas

Insignias: 11

+ 8 más insignias

Equipo

Cal Poly, Team 6-20, Maness Winter 2014 Miembro de Cal Poly, Team 6-20, Maness Winter 2014

CPSU-MANESS-W14S6G20

4 Miembros

11 Guías creadas

0 Comentarios

Agregar un comentario

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 2

Últimos 30 Días: 3

Todo El Tiempo: 350