Repara tus cosas Comunidad Tienda

Canon EOS 300 Back Lock-Release Lever Replacement

Introducción

If the back lock-release lever is loose or broken, this will allow you to attempt to replace it.

Qué necesitas

  1. Canon EOS 300 Back Lock-Release Lever Replacement, Batteries: paso 1, imagen 1 de 3 Canon EOS 300 Back Lock-Release Lever Replacement, Batteries: paso 1, imagen 2 de 3 Canon EOS 300 Back Lock-Release Lever Replacement, Batteries: paso 1, imagen 3 de 3

    • Open up the battery door.

    Editar

  2. Canon EOS 300 Back Lock-Release Lever Replacement: paso 2, imagen 1 de 2 Canon EOS 300 Back Lock-Release Lever Replacement: paso 2, imagen 2 de 2

    • Remove the batteries from the camera by sliding them out into your palm.

    Editar

  3. Canon EOS 300 Back Lock-Release Lever Replacement, Side Panel with Lever: paso 3, imagen 1 de 2 Canon EOS 300 Back Lock-Release Lever Replacement, Side Panel with Lever: paso 3, imagen 2 de 2

    • Release the side latch to open the back panel.

    Editar

  5. Canon EOS 300 Back Lock-Release Lever Replacement: paso 4, imagen 1 de 2 Canon EOS 300 Back Lock-Release Lever Replacement: paso 4, imagen 2 de 2

    • Remove the two black 4.5mm screws above and below the latch.

    Editar

  6. Canon EOS 300 Back Lock-Release Lever Replacement: paso 5, imagen 1 de 2 Canon EOS 300 Back Lock-Release Lever Replacement: paso 5, imagen 2 de 2

    • Using your finger, carefully pry open the side panel from the top of camera.

    • Pull panel downwards to remove.

    • Make sure to keep track of the small black piece of rubber under the latch.

    Editar

  7. Canon EOS 300 Back Lock-Release Lever Replacement, Front Panel: paso 6, imagen 1 de 2 Canon EOS 300 Back Lock-Release Lever Replacement, Front Panel: paso 6, imagen 2 de 2

    • Remove the two silver 6mm Phillips #1 screws.

    Editar

  8. Canon EOS 300 Back Lock-Release Lever Replacement: paso 7, imagen 1 de 2 Canon EOS 300 Back Lock-Release Lever Replacement: paso 7, imagen 2 de 2

    • Flip camera over to the bottom.

    • Remove the one 5mm Phillips #1 silver screw.

    Editar

  9. Canon EOS 300 Back Lock-Release Lever Replacement: paso 8, imagen 1 de 2 Canon EOS 300 Back Lock-Release Lever Replacement: paso 8, imagen 2 de 2

    • Remove the front panel by pulling away from the side with the lever.

    Editar

  10. Canon EOS 300 Back Lock-Release Lever Replacement, Back Lock-Release Lever: paso 9, imagen 1 de 3 Canon EOS 300 Back Lock-Release Lever Replacement, Back Lock-Release Lever: paso 9, imagen 2 de 3 Canon EOS 300 Back Lock-Release Lever Replacement, Back Lock-Release Lever: paso 9, imagen 3 de 3

    • Pull off the lever by pushing up from the bottom and pulling away from the bottom.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

Autor

con 2 otros colaboradores

Jordan Tang

Miembro Desde 01/24/14

590 Reputación

5 Guías creadas

Insignias: 12

+ 9 más insignias

Equipo

Cal Poly, Team 6-20, Maness Winter 2014 Miembro de Cal Poly, Team 6-20, Maness Winter 2014

CPSU-MANESS-W14S6G20

4 Miembros

32 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 3

Ultimos 30 días: 20

Todo El Tiempo: 1,660