Saltar al contenido principal

Cómo crear una Guía de Desmontaje

Qué necesitas

  1. Cómo crear una Guía de Desmontaje, Cómo crear una Guía de Desmontaje: paso 1, imagen 1 de 3 Cómo crear una Guía de Desmontaje, Cómo crear una Guía de Desmontaje: paso 1, imagen 2 de 3 Cómo crear una Guía de Desmontaje, Cómo crear una Guía de Desmontaje: paso 1, imagen 3 de 3
    • Para empezar, decide qué te gustaría desmontar. Algunas de las cosas que no deberías desmontar incluyen:

    • El juguete de tu perro.

    • El marcapasos de tu abuelo.

    • Cualquier dispositivo que contenga plutonio.

    • Optimus Prime

    • A continuación, dirígete a la tienda y compra el dispositivo que hayas escogido. Usar la energía de tus piernas, un recurso altamente ecológico, para el desplazamiento es muy recomendable, pero eres libre de escoger otras opciones.

    • Entra en la tienda, y encuentra el dispositivo. En caso necesario, acampa por fuera de la tienda para ser el primero en conseguirlo.

  2. Cómo crear una Guía de Desmontaje: paso 2, imagen 1 de 3 Cómo crear una Guía de Desmontaje: paso 2, imagen 2 de 3 Cómo crear una Guía de Desmontaje: paso 2, imagen 3 de 3
    • A continuación, encuentra el dispositivo que hayas escogido en la tienda. Intenta no hacerle un placaje a esa adorable señora de 70 años que se lleva la última unidad disponible.

    • No te olvides de pagar el producto. Al contrario de la creencia popular, los poderes mentales Jedi no funcionan con los agentes de seguridad.

    • Rechaza educadamente la extensión de la garantía.

  3. Cómo crear una Guía de Desmontaje: paso 3, imagen 1 de 3 Cómo crear una Guía de Desmontaje: paso 3, imagen 2 de 3 Cómo crear una Guía de Desmontaje: paso 3, imagen 3 de 3
    • Un vez llegues a tu casa, abre la belleza que acabas de adquirir y sumérgete en su superioridad tecnológica. Corre: si lo miras lo suficientemente cerca, verás cómo tu producto está perdiendo valor mientras dudas.

    • No te olvides de hacer como si leyeras el manual de instrucciones durante unos instantes, antes de tirarlo a la basura.

    • Con tu nuevo dispositivo ya en marcha, es hora de disfrutarla todo lo posible. Pero recuerda: agua + aparatos electrónicos = sueños rotos.

  4. Cómo crear una Guía de Desmontaje: paso 4, imagen 1 de 2 Cómo crear una Guía de Desmontaje: paso 4, imagen 2 de 2
    • Asegúrate de tener a mano las herramientas que necesitas.

    • Ten mucho cuidado al desmontar tu dispositivo, a menos que quieras crear una guía sobre cómo destruir tu producto. En ese caso, no tengas ningún cuidado.

    • Lo más importante de todo: ¡diviértete!

  5. Cómo crear una Guía de Desmontaje: paso 5, imagen 1 de 2 Cómo crear una Guía de Desmontaje: paso 5, imagen 2 de 2
    • Es el momento de despejar una zona para las fotos.

    • La iluminación es esencial para unas buenas fotografías. Coloca lámparas y enfócalas en las cercanías de la zona en la que vas a trabajar.

    • Te recomendamos que uses una lámpara portátil conectada a un trípode, con la que podrás enfocar la luz de manera precisa.

    An example of my own lighting setup can be found here: Un ejemplo de una configuración de iluminación.

    Aiden - Contestar

    I find that clear, hi-res PCB images are best achieved with a CCD scanner (not CIS).

    There are numerous examples here:

    http://www.hddoracle.com/viewforum.php?f...

    I use a Canon MP370 multifunction printer/scanner/copier.

    Franc Zabkar - Contestar

    Hm. How might I write a how to. I kinda have other thoughts. Been doing this for a long time. Perhaps the first, a PDP-11, the mainframe of the day. Now days I take photos for myself with an EOS, Use a custom built bench. Start with the chip data sheets and manufacturer claims and test them. I will send a pic of my workbench if you would like. ; ) Thanks

    Ronny L Gonzales - Contestar

  6. Cómo crear una Guía de Desmontaje: paso 6, imagen 1 de 3 Cómo crear una Guía de Desmontaje: paso 6, imagen 2 de 3 Cómo crear una Guía de Desmontaje: paso 6, imagen 3 de 3
    • Con todo el equipo necesario a mano, ya puedes empezar con el desmontaje del dispositivo.

    • Durante el desmontaje, documenta todos los pasos que sigas usando notas y fotos, los cuales podrás compartir con la comunidad de iFixit más tarde.

    • Puedes colocar una hoja en blanco debajo de tu zona de trabajo para obtener mejores fotos.

    • Aquí tienes un ejemplo de una foto tomada en un ambiente con una iluminación de estilo profesional. Los resultados finales variarán, dependiendo del esfuerzo dedicado a crear una zona adecuada de trabajo.

  7. Cómo crear una Guía de Desmontaje: paso 7, imagen 1 de 1
    • Es el momento de compartir lo que has aprendido en el desmontaje con el resto del mundo, usando una de las herramientas tradicionales más honrosas de todos los tiempos: la escritura.

    • Usa tu imaginación y desata tus habilidades como escritor en la comunidad de iFixit.

  8. Cómo crear una Guía de Desmontaje: paso 8, imagen 1 de 1
    • Ahora que tu trabajo está publicado en iFixit, es hora de sentarse, relajarse y disfrutar de la enorme satisfacción de haber creado una guía de desmontaje.

    • Y por qué no, ¡a bailar un poco con el "baile del iPod"!

Conclusión

¡Bien hecho! ¡Has creado tu primera guía de desmontaje! Pero, ¿y por qué parar ahí? ¡Ayuda contestando preguntas!

221 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

en es

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

18 comentarios

I will try to make a Teardown Guide of an old Toshiba Satellite 1400, thanks for the inspiration!

jonasbits - Contestar

Why do I ALWAYS have one screw that strips and won't loosen or tighten, one that is obviously lost in a interdimensional black hole, and weird extra parts when I finish. Or the most vital, irreplaceable, Jesus part breaks, shorts out or disappears? LOL

borg3371 - Contestar

Because lots of machines have more parts than they need. It was suggested by Japanese motor cycle designers and manufactures that the British motor bike industry failed because they just put too many parts in their products and when copiers start they take apart the item and try to reduce the total number and reduce the costs increasing the profits

Mark Fort Te Teko NZ

nashi -

Is a teardown of an old, broken device OK? (I have an LG Optimus L7II with a busted LCD)

niccotaglia - Contestar

Totally! A broken device is a safe pick, you don't need to worry too much about breaking it more, and you might figure out how to replace the broken components!

Sam Goldheart -

Absolutely! Tearing down broken devices is how we learn what makes it tick. Even if you will never never ever get the device working again, the exploration is so worthwhile! Just always be careful with sharp and/or pointy tools. Sometimes tools slip when applying force, so I wear mechanic’s gloves for a little extra protection for my hands, especially when glass or displays are being removed.

Paul Kenyon -

I have a evolve 2 one touch alcatel with only 4 screws to teardown.

dennisp1964 - Contestar

While working on devices and prop replicas, I've found the following useful, even if NOT creating an iFixit teardown:

* Take pics of your steps and the screws, so that when you're faced with reassembly, you have a photo record of which screws went in which hole.

* Keep screws in separate containers, or little Ziploc parts bags (available at hobby and crafts stores, super cheap).

* Mark the individual parts containers or parts bags with a Sharpie, for what the screws are for (e.g. kybd, motherboard, palm rest).

David Spalding - Contestar

As with dismantling anything, it's best to set them out as you taken them off in some sort of reference grid. Or at the very least a photo of what you took off so when you come to that last weird screw that doesn't seem to belong anywhere, all you need do is back track your photos or look at where it came from and where it was left on your reference grid when you took it off.

It pays to prepare, I have a drawer full of "extra" screws, left over prior to finally slowing down and noting where I was putting things and from where they had just been removed.

Colm - Contestar

This is made of win. :D

Quick, cheap and easy tip: Take a fresh sheet off a lint roller, tape it tacky-side up to your work space or a clipboard. Now you have an easy place to put your screws! And they won't roll away! Group them and write the step number with a sharpie for reference.

Jefferson Malone - Contestar

A better use for the pill organizers you can get for a buck will work perfect for placing those tiny screws and keeps them separated, you can label the lids 1, 2, 3, etc. When ready for them open lid 1 when you need the screws for step 1 and so on.

Robert Vantine -

Is there a teardown video for the samsung ativ smart pc 500t. I have one that has a broken earbud port and the internal speakers don't work. I'm thinking there is a relationship with the earbud port and the speakers. When I opened it up I saw what was wrong but not a clear way to disassemble it further. If some has a video I would really appreciate emailing the link to me at eccentric_daughter@yahoo.ca

Eccentric Daughter - Contestar

por que meus parafusos parecem ser uma sujeirinha num piso extremamente branco

villaspark - Contestar

I think a video tear down of various devices would be better. I don’t mind doing a tear down video of a toshiba laptop and uploading it here if possible

Samuel - Contestar

Hey shemzy20, you’re more than welcome to post a video teardown! The same photo and procedure guides still apply, you’ll just upload a video to the introduction of the guide instead of individual steps. Best of luck and happy fixing!

Sam Goldheart -

another solution for those pesky screws that tend to get lost is to use all those refrigerator magnets that your appliance repair men left behind from their last visit, you could glue several of them to a piece of cardboard, cloth, wood etc, or just buy the iFixit protech kit, it comes with a magnet plate

Luis Portilla - Contestar

Do I have this right? The purpose of a teardown is to discover how to take a product apart and get inside without destroying it —and so you can put it back together. So the purpose of a teardown is not to troubleshoot a specific defect. That is what a repair guide is for. I’m seeing this as Part 1: Teardown. Part 2: Write a repair guide. What do you think?

John Wackman - Contestar

Hey John, that’s about right!

We consider teardowns to be an exploration of the device—its design, repairability, and the procedures needed to get in. After a teardown you’ve got more experience to make guides to address hardware problems. Troubleshooting should start with software things (have you tried turning it off and on again) and then move into hardware replacements using the guides the teardown helped create!

Sam Goldheart -

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 9

Ultimos 7 días: 55

Ultimos 30 días: 294

Todo El Tiempo: 109,272