Menú

Tus configuraciones

Brother PT-110 Printer Motor Replacement

Escrito Por: Kimberly Larsen (y 3 de otros participantes)
  • Comentarios: 0
  • Favoritos: 0

Dificultad

Moderar

Pasos

11

Tiempo Requerido

Sugerir un tiempo??

Secciones

3

Banderas

1

Featured Student Guide

Guía de Estudiante Destacada

Esta guía fue realizada gracias al duro trabajo de nuestros fantásticos estudiantes y ha sido valorada como excepcionalmente genial por el personal de iFixit.

Introducción

The printer motor is located behind the keyboard, near the middle of the device. To access it, the back panel needs to be snapped off and the printer cartridge taken out. The middle panel needs to be unscrewed, and the motor should be visible.

Herramientas

Comprar estas herramientas

Partes

No se especificaron partes.

  1. Push on the side of the cover, and remove it. Push on the side of the cover, and remove it.

    • Push on the side of the cover, and remove it.

    Editar

  2. Remove the batteries.

    • Remove the batteries.

    Editar

  3. Unscrew the two 9 mm Phillips #1 screws from the top and bottom. Total: 2 x Screws

    • Unscrew the two 9 mm Phillips #1 screws from the top and bottom.

    • Total: 2 x Screws

    Editar

  4. First: To separate the top cover from the body, insert a spudger between the two halves.

    • First: To separate the top cover from the body, insert a spudger between the two halves.

    • Gently twist the spudger until the two halves separate. Do this in multiple spots around the perimeter of the cover to distribute the pressure.

    • DO NOT PULL HALVES APART. There are wired connections inside that must be disconnected before halves can be fully separated.

    Editar

  6. Gently separate the two covers, ensuring wires are not taut.

    • Gently separate the two covers, ensuring wires are not taut.

    Editar

  7. Gently grasp the ribbon wire and top cover, then gently pull the ribbon wire out of its connection.

    • Gently grasp the ribbon wire and top cover, then gently pull the ribbon wire out of its connection.

    Editar

  8. Carefully pinch the top of the connector. Pull perpendicular to the device until the wire is disconnected.

    • Carefully pinch the top of the connector.

    • Pull perpendicular to the device until the wire is disconnected.

    • It may require more force than expected to disconnect the wires.

    Editar

  9. Unscrew the three 9 mm Phillips #1 screws shown. Total: 3 x Screws Total: 3 x Screws

    • Unscrew the three 9 mm Phillips #1 screws shown.

    • Total: 3 x Screws

    Editar

  10. Remove the motor housing.

    • Remove the motor housing.

    Editar

  11. Unscrew the two 3 mm Phillips #1 screws from the motor housing. Total: 2 x Screws

    • Unscrew the two 3 mm Phillips #1 screws from the motor housing.

    • Total: 2 x Screws

    Editar

  12. Remove the motor.

    • Remove the motor.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 3 otros colaboradores

Kimberly Larsen

Miembro Desde 28/09/16

171 Reputación

5 Guías creadas

Insignias: 6

+ 3 más insignias

Equipo

IUPUI, Team 1-1, Harley Fall 2016 Miembro de IUPUI, Team 1-1, Harley Fall 2016

IUPUI-HARLEY-F16S1G1

3 Miembros

7 Guías creadas

0 comentarios

Agregar un comentario

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 2

Ultimos 30 días: 7

Todo El Tiempo: 294