Repara tus cosas Comunidad Tienda

Brother PT-110 Keypad Contacts Replacement

Introducción

This guide will show you how to take apart the back panel to replace the keypad contacts.

Qué necesitas

  1. Brother PT-110 Keypad Contacts Replacement, Batteries: paso 1, imagen 1 de 2 Brother PT-110 Keypad Contacts Replacement, Batteries: paso 1, imagen 2 de 2

    • Push on the side of the cover, and remove it.

    Traducir

  2. Brother PT-110 Keypad Contacts Replacement: paso 2, imagen 1 de 1

    • Remove the batteries.

    Traducir

  3. Brother PT-110 Keypad Contacts Replacement, Back Plate: paso 3, imagen 1 de 2 Brother PT-110 Keypad Contacts Replacement, Back Plate: paso 3, imagen 2 de 2

    • Unscrew the two 9 mm Phillips #1 screws from the top and bottom.

    • Total: 2 x Screws

    Traducir

  4. Brother PT-110 Keypad Contacts Replacement: paso 4, imagen 1 de 1

    • First: To separate the top cover from the body, insert a spudger between the two halves.

    • Gently twist the spudger until the two halves separate. Do this in multiple spots around the perimeter of the cover to distribute the pressure.

    • DO NOT PULL HALVES APART. There are wired connections inside that must be disconnected before halves can be fully separated.

    Traducir

  6. Brother PT-110 Keypad Contacts Replacement: paso 5, imagen 1 de 1

    • Gently separate the two covers, ensuring wires are not taut.

    Traducir

  7. Brother PT-110 Keypad Contacts Replacement: paso 6, imagen 1 de 1

    • Gently grasp the ribbon wire and top cover, then gently pull the ribbon wire out of its connection.

    Traducir

  8. Brother PT-110 Keypad Contacts Replacement: paso 7, imagen 1 de 2 Brother PT-110 Keypad Contacts Replacement: paso 7, imagen 2 de 2

    • Carefully pinch the top of the connector.

    • Pull perpendicular to the device until the wire is disconnected.

    • It may require more force than expected to disconnect the wires.

    Traducir

  9. Brother PT-110 Keypad Contacts Replacement: paso 8, imagen 1 de 3 Brother PT-110 Keypad Contacts Replacement: paso 8, imagen 2 de 3 Brother PT-110 Keypad Contacts Replacement: paso 8, imagen 3 de 3

    • Unscrew the three 9 mm Phillips #1 screws shown.

    • Total: 3 x Screws

    Traducir

  10. Brother PT-110 Keypad Contacts Replacement, Keypad Contacts: paso 9, imagen 1 de 2 Brother PT-110 Keypad Contacts Replacement, Keypad Contacts: paso 9, imagen 2 de 2

    • Unscrew both 6 mm Phillips #1 screws from the circuit board.

    • Total screws: 2

    Traducir

  11. Brother PT-110 Keypad Contacts Replacement: paso 10, imagen 1 de 1

    • Gently lift the circuit board out.

    Traducir

  12. Brother PT-110 Keypad Contacts Replacement: paso 11, imagen 1 de 1

    • Peel the keypad contacts up from the plastic casing.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 3 otros colaboradores

Kimberly Larsen

Miembro Desde 09/28/16

237 Reputación

5 Guías creadas

Insignias: 11

+ 8 más insignias

Equipo

IUPUI, Team 1-1, Harley Fall 2016 Miembro de IUPUI, Team 1-1, Harley Fall 2016

IUPUI-HARLEY-F16S1G1

3 Miembros

7 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 0

Todo El Tiempo: 316