Repara tus cosas Comunidad Tienda

Braven BRV-X Button Module(s) Replacement

Introducción

If the buttons on your speaker are not working, they may need to be replaced. Use this guide to replace the button module on your Braven BRV-X.

Qué necesitas

  1. Braven BRV-X Button Module(s) Replacement, Front Speaker Panel: paso 1, imagen 1 de 1

    • Remove four 1.1 cm outer screws in the outer shell using the Phillips #00 screwdriver.

    Editar

  2. Braven BRV-X Button Module(s) Replacement: paso 2, imagen 1 de 1

    • Remove four 1.3 cm inner screws in the outer shell using the 1.5mm Hex screwdriver.

    Editar

  3. Braven BRV-X Button Module(s) Replacement: paso 3, imagen 1 de 1

    • Gently remove the outer shell.

    Editar

  4. Braven BRV-X Button Module(s) Replacement: paso 4, imagen 1 de 2 Braven BRV-X Button Module(s) Replacement: paso 4, imagen 2 de 2

    • Cut adhesive tape on both sides.

    Editar

  5. Braven BRV-X Button Module(s) Replacement: paso 5, imagen 1 de 2 Braven BRV-X Button Module(s) Replacement: paso 5, imagen 2 de 2

    • Remove eighteen 0.9cm screws in the inner shell using the Phillips #00 screwdriver.

    Editar

  7. Braven BRV-X Button Module(s) Replacement: paso 6, imagen 1 de 3 Braven BRV-X Button Module(s) Replacement: paso 6, imagen 2 de 3 Braven BRV-X Button Module(s) Replacement: paso 6, imagen 3 de 3

    • Pry open the glued inner shell using a spudger around all sides of the shell.

    • Don't use too much pressure as that could cause damage to the plastic.

    Editar

  8. Braven BRV-X Button Module(s) Replacement: paso 7, imagen 1 de 2 Braven BRV-X Button Module(s) Replacement: paso 7, imagen 2 de 2

    • Remove ten 0.7 cm screws in the front plate using the 1.5 mm Hex screwdriver.

    Editar

  9. Braven BRV-X Button Module(s) Replacement: paso 8, imagen 1 de 2 Braven BRV-X Button Module(s) Replacement: paso 8, imagen 2 de 2

    • Use a spudger to open the front speaker plate.

    Editar

  10. Braven BRV-X Button Module(s) Replacement: paso 9, imagen 1 de 1

    • Remove three 1.0 cm screws from the battery unit.

    • It is recommended (but not required) to remove the battery.

    Editar

  11. Braven BRV-X Button Module(s) Replacement: paso 10, imagen 1 de 2 Braven BRV-X Button Module(s) Replacement: paso 10, imagen 2 de 2

    • Disconnect the ribbon cable attached the main board.

    Editar

  12. Braven BRV-X Button Module(s) Replacement: paso 11, imagen 1 de 3 Braven BRV-X Button Module(s) Replacement: paso 11, imagen 2 de 3 Braven BRV-X Button Module(s) Replacement: paso 11, imagen 3 de 3

    • Pry open the second plate holding in the speaker using a spudger around all sides.

    • It is recommended to use a spudger to remove the heavily glued areas between the plates before prying.

    • Don't use too much pressure as that could cause damage to the plastic.

    Editar

  13. Braven BRV-X Button Module(s) Replacement: paso 12, imagen 1 de 3 Braven BRV-X Button Module(s) Replacement: paso 12, imagen 2 de 3 Braven BRV-X Button Module(s) Replacement: paso 12, imagen 3 de 3

    • Cut the 20 gauge wires attached to the front IR sensor and two speaker wires.

    • Leave enough length on the wire to work with it afterwards.

    • Cut the 22 gauge wire attached in the corner.

    • Solder the new speaker plate during reassembly.

    • To properly solder and desolder connections, visit the How to Solder and Desolder Connections guide.

    Editar

  14. Braven BRV-X Button Module(s) Replacement, Button Module(s): paso 13, imagen 1 de 2 Braven BRV-X Button Module(s) Replacement, Button Module(s): paso 13, imagen 2 de 2

    • Remove the ribbon cable attached to the main board.

    • Pull from the clip and not from the cable.

    Editar

  15. Braven BRV-X Button Module(s) Replacement: paso 14, imagen 1 de 1

    • Remove three 0.7 cm screws from the button module(s) using the Phillips #00 screwdriver.

    Editar

  16. Braven BRV-X Button Module(s) Replacement: paso 15, imagen 1 de 1

    • Gently lift the button module from the enclosure.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 1 otro colaborador

Trey Peterson

Miembro Desde 04/01/19

301 Reputación

2 Guías creadas

Insignias: 3

Equipo

IUPUI, Team S1-G5, Harley Spring 2019 Miembro de IUPUI, Team S1-G5, Harley Spring 2019

IUPUI-HARLEY-S19S1G5

3 Miembros

2 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 1

Ultimos 30 días: 6

Todo El Tiempo: 393