Repara tus cosas Comunidad Tienda

Bowers and Wilkins T7 Battery Replacement

Introducción

Use this guide to learn how to replace your battery for the Bowers and Wilkins T7 Bluetooth Speaker.

Qué necesitas

  1. Bowers and Wilkins T7 Battery Replacement, Access Panel: paso 1, imagen 1 de 1

    • As with all electronic devices, make sure your device is powered off before you begin.

    • Gently lift up the access panel; it should easily "pop" open.

    Editar

  2. Bowers and Wilkins T7 Battery Replacement: paso 2, imagen 1 de 1

    • Remove 14mm screws on the front panel with a J1 Phillips head screwdriver.

    • There are 8 screws in total.

    Editar

  3. Bowers and Wilkins T7 Battery Replacement: paso 3, imagen 1 de 2 Bowers and Wilkins T7 Battery Replacement: paso 3, imagen 2 de 2

    • Be gentle, the rubber seal is fragile and easy to tear, resulting in cosmetic damage to your device.

    • Using the ifixit Opening Tool, carefully pry off the rubber seal around the sides.

    • The seal is held by adhesive, if this is proving difficult you can use a heat gun to help the process.

    Editar

  5. Bowers and Wilkins T7 Battery Replacement: paso 4, imagen 1 de 2 Bowers and Wilkins T7 Battery Replacement: paso 4, imagen 2 de 2

    • The cover is the most difficult part to remove. As you work, pry continuously, moving the tool around the device, working it a little further as you go.

    • Using the ifixit Opening Tool, pry open at the seam found under the rubber seal.

    • As the cover starts to come off, you can lift up using your hand.

    Editar

  6. Bowers and Wilkins T7 Battery Replacement: paso 5, imagen 1 de 3 Bowers and Wilkins T7 Battery Replacement: paso 5, imagen 2 de 3 Bowers and Wilkins T7 Battery Replacement: paso 5, imagen 3 de 3

    • Gently squeeze the internal locking mechanism inside the red and white terminals with either your fingers or a pair of precision tweezers.

    • While squeezing the internal locking mechanism, pull back the terminal.

    • Repeat this process for the second speaker.

    Editar

  7. Bowers and Wilkins T7 Battery Replacement, Battery: paso 6, imagen 1 de 1

    • Using a cutting tool such as a Jimmy steel blade or wire cutter, cut the cable tie surrounding the battery.

    • Be careful not to damage the battery while cutting the cable tie surrounding the battery.

    Editar

  8. Bowers and Wilkins T7 Battery Replacement: paso 7, imagen 1 de 2 Bowers and Wilkins T7 Battery Replacement: paso 7, imagen 2 de 2

    • Using the ifixit Opening Tool, pry out the battery power supply connector.

    • Pull and remove the battery power supply connector.

    Editar

  9. Bowers and Wilkins T7 Battery Replacement: paso 8, imagen 1 de 2 Bowers and Wilkins T7 Battery Replacement: paso 8, imagen 2 de 2

    • After disconnecting the power supply connector, pull the battery out of its case.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

8 personas más completaron esta guía.

Autor

con 2 otros colaboradores

Bertrand Plummer

Miembro Desde 02/28/17

251 Reputación

1 Guía escrita

Insignias: 6

+ 3 más insignias

Equipo

USF Tampa, Team S7-G1, Cagle Spring 2017 Miembro de USF Tampa, Team S7-G1, Cagle Spring 2017

USFT-CAGLE-S17S7G1

5 Miembros

4 Guías creadas

3 comentarios

Bravo ! Le choix de cet appareil symbolique !

Pierre Vanhoorenbeeck - Contestar

Seriously

Couldn't the lady get her

'nails did’

Lux Valet - Contestar

No repair any repairing sentar

Abdul Malik Parvez - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 26

Ultimos 30 días: 112

Todo El Tiempo: 9,383