Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Tienda

Introducción

Follow this guide to replace the the button switch circuit board on the Bose SoundLink Mini speaker. The button switch circuit board is located deep within the body of the speaker. It may be necessary to replace this part if the buttons on the speaker no longer work properly. Make sure you have the necessary tools and follow the guide step by step to replace this part.

Partes

No se especificaron partes.

  1. Peel back the rubber battery cover and remove the four circled 6.0 mm screws using a T8 Torx Screwdriver.
    • Peel back the rubber battery cover and remove the four circled 6.0 mm screws using a T8 Torx Screwdriver.

    Help I removed the part which I'm not supposed to next to the battery charger how do I put it back?

    Sooraj murali - Contestar

    Where can I actually get a replacement battery????

    appreciate any help bc I couldn’t find it anywhere.

    Kamil M. - Contestar

    Where can I get an actual replacement battery???

    appreciate any help bc I couldn’t find it anywhere.

    Kamil M. - Contestar

    Hi Brent and thank you for this easy fix.

    Still I have a problem I did not have while the original battery was in place: the sound is now buzzing even at a middle-of-the-range volume.

    I used the original screws and everything seems in place and the screws are tightened “right” I would say. I am usually fine fixing things. And I do not see what I could have done wrong…

    Any suggestion?

    Thank you.

    MBP - Contestar

    Which battery is the correct one. Two model are shown to be purchase

    Ruben Roman - Contestar

    What is not discussed is the wires that connect the battery to the speaker. In mine, I think I destroyed the speaker, because I pulled out the battery and dislodged the wires from the electronic board. I think they must have been soldered on, and now am having trouble attaching the new wires to the board.

    horseylawgal - Contestar

  2. While holding the cover back, pull straight up on the battery to remove it. While holding the cover back, pull straight up on the battery to remove it.
    • While holding the cover back, pull straight up on the battery to remove it.

    Where can I buy this battery

    Karsten lou nielsen - Contestar

    Well that part was simple. What I need is how to disconnect the ribbon cable which is soldered in on both ends. No help here.

    Art Kennedy - Contestar

    soweit sogut..aber die Kabel sind verlötet ?

    das ist ja das problem

    also sehr schlechte Anleitung da ja das wichtigste fehlt !!

    Armin Karl - Contestar

    Bonjour pas aussi simple car les câbles de la batterie d origine sont soudés…

    Lionel Ludosky - Contestar

  3. Insert the Metal Spudger between the rubber edge on the grille and the aluminum casing.
    • Insert the Metal Spudger between the rubber edge on the grille and the aluminum casing.

    • Place Metal Spudger in the location shown.

    Woher bekomme ich nun rin solches Vorder- und Rückgitter?

    [COBS]CR4ZY BLITZ - Contestar

  4. Slowly pry up the grille until the two tabs shown pop out. Be very gentle, the grille will bend.
    • Slowly pry up the grille until the two tabs shown pop out.

    • Be very gentle, the grille will bend.

  5. The grille is attached to the speaker with double sided sticky tape. To remove the grill gently pull upward while keeping tension to the right. Be very gentle, the grille will bend.
    • The grille is attached to the speaker with double sided sticky tape. To remove the grill gently pull upward while keeping tension to the right.

    • Be very gentle, the grille will bend.

  6. Repeat steps to remove the back grille. Repeat steps to remove the back grille.
    • Repeat steps to remove the back grille.

  7. Remove the four 15.0 mm screws on the left and the four 9.0 mm screws on the right using the T8 Torx Screwdriver. Remove the four 15.0 mm screws on the left and the four 9.0 mm screws on the right using the T8 Torx Screwdriver.
    • Remove the four 15.0 mm screws on the left and the four 9.0 mm screws on the right using the T8 Torx Screwdriver.

  8. Remove the circuit board by pushing it with your index finger in the direction shown while using a nylon or metal spudger to lift it up and out of place. Remove the circuit board by pushing it with your index finger in the direction shown while using a nylon or metal spudger to lift it up and out of place.
    • Remove the circuit board by pushing it with your index finger in the direction shown while using a nylon or metal spudger to lift it up and out of place.

  9. Carefully pull on the battery cover until the rubber tab slides out of the aluminum casing. Carefully pull on the battery cover until the rubber tab slides out of the aluminum casing.
    • Carefully pull on the battery cover until the rubber tab slides out of the aluminum casing.

    I just want to emphasize that the rubber tab (that is part of the cover) is supposed to sit ON TOP of the circuit board. In my case, my son managed to pull of the battery cover off completely, so as I was taking it apart I didn’t see how the rubber tab was actually supposed to sit inside the box. Because these instructions have you unseat the circuit board, I thought it was implying the tab was supposed to sit under the circuit board. But that is NOT the case! If I had looked at the pictures 7 and 9 more carefully, I would have seen how things were supposed to sit. Instead I first jammed things back together with the rubber underneath the board (really hard to do), only to find that the slightly squeezed rubber tab pushed the cover out a millimeter so it wouldn’t sit right on the charger. On closer inspection, I figured things out.

    Matthew Busche - Contestar

  10. Remove the sponge (save for later replacement) and gently flip the black tab 90 degrees to release the connectors grip on the ribbon cable. Remove the ribbon cable from the connector.
    • Remove the sponge (save for later replacement) and gently flip the black tab 90 degrees to release the connectors grip on the ribbon cable. Remove the ribbon cable from the connector.

    • The black tab must be flipped up in order to reinsert the ribbon cable on reassembly.

    there’s supposed to be a wire strips lock behind that small,gray foam,careful fellas don’t end it like me,i just simply pulling it off until it teared apart the board, also it broked,and until know i haven’t fix it yet

    Kikay CianancyTM - Contestar

  11. Use a Metal Spudger to pry up the plastic divider. Use a Metal Spudger to pry up the plastic divider. Use a Metal Spudger to pry up the plastic divider.
    • Use a Metal Spudger to pry up the plastic divider.

  12. When removing the plastic divider be careful not to damage the wire strip sliding through it. When removing the plastic divider be careful not to damage the wire strip sliding through it.
    • When removing the plastic divider be careful not to damage the wire strip sliding through it.

  13. Reach through the battery compartment hole and unplug the power strip shown. Reach through the battery compartment hole and unplug the power strip shown.
    • Reach through the battery compartment hole and unplug the power strip shown.

    Hi ineed complete surkit bord for bose sound link mini speaker

    Ajay kumar - Contestar

    Bose sound link mini 1 complete surkit prece?

    Ajay kumar - Contestar

  14. Remove both circuit boards by wiggling them up and out of the casing. Unplug the speaker wires connected and fully remove both circuit boards. When unplugging the speaker wires, squeeze the white connector piece to release the wires.
    • Remove both circuit boards by wiggling them up and out of the casing.

    • Unplug the speaker wires connected and fully remove both circuit boards.

    • When unplugging the speaker wires, squeeze the white connector piece to release the wires.

  15. Unhook the speaker wires clipped onto the button switch circuit board. Unhook the speaker wires clipped onto the button switch circuit board.
    • Unhook the speaker wires clipped onto the button switch circuit board.

  16. Use a nylon or metal spudger to slightly lift up on the button switch circuit board. Pull the button switch circuit board straight out from the casing.
    • Use a nylon or metal spudger to slightly lift up on the button switch circuit board.

    • Pull the button switch circuit board straight out from the casing.

    Hi

    my bose SoundLink mini keep flashing ember light even it’s plugged into AC adapter,can you tell me how can I get it update

    Moqdam Aljwrany - Contestar

Conclusión

To reassemble your device, follow these instructions in reverse order.

6 personas más completaron esta guía.

Jordan Smith

Miembro Desde 01/10/15

746 Reputación

4 Guías creadas

Equipo

Cal Poly, Team 1-23, Maness Fall 2015 Miembro de Cal Poly, Team 1-23, Maness Fall 2015

CPSU-MANESS-F15S1G23

4 Miembros

15 Guías creadas

Hello

Where I can buy circuit

candellaaria - Contestar

Yes were can we get the replacement part? ?

sonny goddin - Contestar

Hi sonny,

did you find this part ? (the first circuit board)

luc.lacouture -

Hi

Can you get the relacement part for the mini II or is it the same - and if

- where and how to order for delivery to Europe?

Andreas Burckhart - Contestar

Kindly can you tell me is th bose Soundlink mini first generation has an update or not, because it started no charge and the ember ligy keep flashing and some times reed color , I bought a new battery but still the same now it’s playing up

Moqdam Aljwrany - Contestar

SOLVED:

Hey, check the ends of the ribbon cables on the circuit board for corrosion where the cable goes in to the plug, as this is a common problem to why the batterys don't get enough charge, (yellow to red light to dead…)

Also, when the Batterys drain down to much… There is a low voltage cut off switch circuit board hidden in the battery pack. You must manually charge the battery past 7.4v for it to trigger “ON” power to the bose speaker (its a low voltage lipo fire battery protection feature thing).

However to do this… you must carefully crack the battery pack open and pull out the Batterys to get to the positive and negative terminals of the 2 lipo cells,

Do not try to charge the pack from the multi pin socket on the outside of the battery case… As the power goes through a circuit board before reaching the Batterys… Blow that and you might as well throw the whole battery in the bin, as that power management circuit board splits the power and has many micro chips… Just go straight for the battery cell.

justin meynell -

Same thing here, can’t find replacement parts. I need to replace the input board.

deusmarjuninho - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 3

Ultimos 7 días: 82

Ultimos 30 días: 331

Todo El Tiempo: 17,380