Repara tus cosas Comunidad Tienda

Black and Decker WP900 Motor Replacement

Introducción

This page gives instructions for disassembling the Black and Decker WP900 6-Inch Orbital Waxer and Polisher to the point where the motor can be fully removed and replaced.

Qué necesitas

  1. Black and Decker WP900 Motor Replacement, Motor: paso 1, imagen 1 de 1

    • Using the plastic tool, detach the handle tab as shown.

    • Make sure the device is unplugged.

    Editar

  2. Black and Decker WP900 Motor Replacement: paso 2, imagen 1 de 1

    • Using the Philips #1 screwdriver, unscrew all of the screws. There should be 8-30mm screws to remove.

    • Be sure to keep track of where each screw was placed in the device for later reassembly.

    Editar

  3. Black and Decker WP900 Motor Replacement: paso 3, imagen 1 de 3 Black and Decker WP900 Motor Replacement: paso 3, imagen 2 de 3 Black and Decker WP900 Motor Replacement: paso 3, imagen 3 de 3

    • Remove the back panel of the external casing, leaving all internal components resting in the front panel.

    • Remove the black handle from the main external casing.

    Editar

  5. Black and Decker WP900 Motor Replacement: paso 4, imagen 1 de 1

    • Loosen the power cord and control panel. Using the Phillips #1 screwdriver, remove two 22mm screws.

    • The metal bracket will detach with the two screws.

    • Using the Flathead 3/32" screwdriver, remove two 22mm screws.

    Editar

  6. Black and Decker WP900 Motor Replacement: paso 5, imagen 1 de 2 Black and Decker WP900 Motor Replacement: paso 5, imagen 2 de 2

    • Gently pull the power cord out from the control module.

    • Remember, when you're reassembling the device, the black wire should be on the top.

    Editar

  7. Black and Decker WP900 Motor Replacement: paso 6, imagen 1 de 1

    • Firmly grasping the motor, dislodge the internal components from the frontal external casing.

    • Switch and control panel are attached to the motor.

    Editar

  8. Black and Decker WP900 Motor Replacement: paso 7, imagen 1 de 2 Black and Decker WP900 Motor Replacement: paso 7, imagen 2 de 2

    • Using a Phillips #1 screwdriver, remove the two 22mm screws securing the brush assembly to the motor.

    Editar

  9. Black and Decker WP900 Motor Replacement: paso 8, imagen 1 de 2 Black and Decker WP900 Motor Replacement: paso 8, imagen 2 de 2

    • To fully remove the brush assembly from the motor, push the brushes (enclosed in the gold ribbing) outward and pull up.

    Editar

  10. Black and Decker WP900 Motor Replacement: paso 9, imagen 1 de 1

    • With a large amount of force, pull the motor up and off of the wire coil.

    Editar

    The pad itself have fallen while im using it, can i still fix it?

    leworx_13 - Contestar

    The backing plate has drop can i still fix it? Please help

    leworx_13 - Contestar

    Do we know where we can order this motor part?

    Grant Gattuso - Contestar

Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Autor

con 2 otros colaboradores

Stefan Wolowec

Miembro Desde 02/15/16

128 Reputación

1 Guía escrita

Insignias: 7

+ 4 más insignias

Equipo

IUPUI, Team 8-8, Wilson Spring 2016 Miembro de IUPUI, Team 8-8, Wilson Spring 2016

IUPUI-WILSON-S16S8G8

4 Miembros

4 Guías creadas

Un comentario

Very straightforward tutotial. We are writing review of this product here https://www.helpful.reviews/en/product/4.... However we have not found many cases among owners of this product that they would need to repair motor by its replacement.

John Bazmek - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 6

Ultimos 30 días: 16

Todo El Tiempo: 2,260