Introducción

Learn how to manipulate your Black and Decker Toast R Oven in order to clean it, to replace its door-spring mechanism, and/or to replace its damaged door.

  1. Make sure that the toaster is unplugged before you begin.
    • Make sure that the toaster is unplugged before you begin.

    • Turn the toaster over with its backside face down.

    • Remove the two Phillips #4 1cm screws that attach the side panels.

    Agregar Comentario

  2. Pull downwards (towards the bottom of the unit) and outward to remove the side panels.
    • Pull downwards (towards the bottom of the unit) and outward to remove the side panels.

    Agregar Comentario

    • Remove the metal vent piece that is below the door.

    • This should slide off easily once both of the side panels are removed.

    Agregar Comentario

    • Remove the two Phillips #4 1 cm screws, which connect the bottom panel to the unit.

    Agregar Comentario

    • Remove the crumb tray (the bottom, metal panel) from the toaster unit.

    Agregar Comentario

    • Remove the aluminum strip from the bottom of unit; this is the piece that is directly under the door.

    Agregar Comentario

    • Remove the knobs by pulling them upward; they should slide right off.

    • When placing the knobs back on the unit, make sure the semicircle notch fits correctly in the hole so that the knobs don't fall off.

    Agregar Comentario

  3. Reparte el espíritu de reparación esta Navidad
    Obtén $12 de descuento en tu compra de $50 o más con el código FIXMAS12
    Reparte el espíritu de reparación esta Navidad
    Obtén $12 de descuento en tu compra de $50 o más con el código FIXMAS12
    • Unhook the bottom of the the display panel from the toaster unit.

    • It will be a little tough to pry off, but don't be afraid to be forceful. You can use your hands, or pliers, to bend the metal piece backwards.

    Agregar Comentario

    • Begin to detach the back panel from the toaster unit.

    • Then, unhook the rest of the display panel.

    • This will also be a little tough to get off, but don't be afraid to be forceful.

    Agregar Comentario

    • Now, you can clean the outside units of the toaster oven.

    Agregar Comentario

    • Remove the the heating coil protection bar from the toaster unit by first pulling out the left side.

    Agregar Comentario

    • Finish removing the outside cover by lifting the lid upward.

    Agregar Comentario

    • Remove the four Phillips #4 1 cm screws from the back of the unit.

    Agregar Comentario

    • Use the screwdriver to remove the spring from the unit.

    • Place the screwdriver inside the spring loop.

    • Pull to unhinge the spring from the back panel.

    Agregar Comentario

    • Remove the spring from the door mechanism by pulling it off.

    • Replace the old spring with a new spring.

    • When inserting a new spring, make sure that the spring is connected to the lower hole of the back panel (the hole above is used for the back casing).

    Agregar Comentario

    • Use the pliers and a wrench to straighten the outdoor mechanism.

    Agregar Comentario

    • Take off the left side of the door by separating the unit from the hinge.

    Agregar Comentario

    • Separate the right side of the door from the unit as in the previous step.

    Agregar Comentario

    • Separate the door mechanism from the door by tilting the door to relieve the mechanism.

    Agregar Comentario

    • Unscrew the two door-handle screws.

    Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

Jonathan

Miembro Desde 18/09/12

135 Reputación

5 Guías creadas

Equipo

Cal Poly, Team 2-10, Propen Fall 2012 Miembro de Cal Poly, Team 2-10, Propen Fall 2012

CPSU-PROPEN-F12S2G10

4 Miembros

5 Guías creadas

sale humo al momento de prender el horno

alo_68salud - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 3

Últimos 7 Días: 11

Últimos 30 Días: 149

Todo El Tiempo: 3,271