Repara tus cosas Comunidad Tienda

Axess TA2513-10WT Speaker Replacement

Introducción

In this guide you will find steps on how to remove the speakers from the Axess TA2513-10WT tablet in order to replace them. The guide will show you how to access the tablet's circuit board, identify the right and left speakers, and how to remove the speakers from the circuit board.

Qué necesitas

  1. Axess TA2513-10WT Speaker Replacement, Back Cover: paso 1, imagen 1 de 1

    • Lay the tablet down on a flat surface with the screen facing up, and the external camera facing upwards and closest to you.

    Editar

  2. Axess TA2513-10WT Speaker Replacement: paso 2, imagen 1 de 3 Axess TA2513-10WT Speaker Replacement: paso 2, imagen 2 de 3 Axess TA2513-10WT Speaker Replacement: paso 2, imagen 3 de 3

    • Insert the plastic opening tool in the space between the screen and the back cover above the volume buttons.

    • Slide the plastic opening tool gently along the sides.

    • If a small gap is not created between the screen and the back cover, pry gently upward at each of these latching points.

    Editar

  3. Axess TA2513-10WT Speaker Replacement: paso 3, imagen 1 de 1

    • Place the spudger in an open space to keep the back case from shutting while you continue to slide the opening tool.

    Editar

  4. Axess TA2513-10WT Speaker Replacement: paso 4, imagen 1 de 1

    • Remove the back cover with your hands once all points have been unlatched. It should separate completely from the screen that contains the battery and chip components.

    Editar

  6. Axess TA2513-10WT Speaker Replacement, Speaker: paso 5, imagen 1 de 1

    • Remove tape attached to black and red speaker wires.

    Editar

  7. Axess TA2513-10WT Speaker Replacement: paso 6, imagen 1 de 1

    • Identify the four speaker nodes.

    • From left to right the nodes are "SPKP1", "SPKN1", "LN", and "LP"

    Editar

  8. Axess TA2513-10WT Speaker Replacement: paso 7, imagen 1 de 1

    • Place the soldering tool on the speaker node labeled "SPKP1" and quickly remove the red wire with tweezers.

    Editar

  9. Axess TA2513-10WT Speaker Replacement: paso 8, imagen 1 de 1

    • Place the soldering tool on the speaker node labeled "SPKN1" and quickly remove the black wire with tweezers.

    Editar

  10. Axess TA2513-10WT Speaker Replacement: paso 9, imagen 1 de 1

    • Place the soldering tool on the speaker node labeled "LP" and quickly remove the black wire with the tweezers.

    Editar

  11. Axess TA2513-10WT Speaker Replacement: paso 10, imagen 1 de 1

    • Place the soldering tool on the speaker node labeled "LN" and quickly remove the red wire with tweezers.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 7 otros colaboradores

Steven Kavanagh

Miembro Desde 03/24/15

301 Reputación

3 Guías creadas

Insignias: 3

Equipo

Baylor, Team 6-3, Shaver Spring 2015 Miembro de Baylor, Team 6-3, Shaver Spring 2015

BU-SHAVER-S15S6G3

3 Miembros

10 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 0

Todo El Tiempo: 299