Repara tus cosas Comunidad Tienda

Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.

Qué necesitas

  1. Este paso está sin traducir. Ayuda a traducirlo

    : paso 1, imagen 1 de 2 : paso 1, imagen 2 de 2

    • Use your fingernail to gently pry off the phone's back cover at the indicated location. While your fingernail is under the back cover slide your finger around the edges of the phone until the cover pops off.

    Traducir

  2. Este paso está sin traducir. Ayuda a traducirlo

    : paso 2, imagen 1 de 1

    • Remove the thirteen black screws and the single silver screw from the back of the phone with a JIS size 00 screwdriver.

    • The black screws are 2.8 mm in length.

    • The silver screw is 5.5 mm in length.

    • The black screw next to the camera and the flash is covered by a sticker. This screw can be easily removed as if there were no sticker on top of it. The point of the screwdriver should be able to pierce through the sticker easily.

    Traducir

  3. Este paso está sin traducir. Ayuda a traducirlo

    : paso 3, imagen 1 de 2 : paso 3, imagen 2 de 2

    • Use a plastic opening tool to remove the inner phone backing.

    • The parts of the inner backing held down by two strips of double sided tape can be easily loosened by inserting the plastic opening tool underneath it and gently lifting it up.

    Traducir

  4. Este paso está sin traducir. Ayuda a traducirlo

    : paso 4, imagen 1 de 1

    • Note the position of the speaker unit so you can replace it in the correct place during reassembly.

    • Take the speaker out of the back of the phone. It should come out easily as soon as the inner back is removed because nothing is holding it down in place anymore.

    Traducir

  6. Este paso está sin traducir. Ayuda a traducirlo

    : paso 5, imagen 1 de 1

    • Use a plastic prying tool to carefully detach the bottom part of the antenna.

    • The antenna can be easily bent out of shape. Be sure to lift from underneath the cable as shown.

    Traducir

  7. Este paso está sin traducir. Ayuda a traducirlo

    : paso 6, imagen 1 de 2 : paso 6, imagen 2 de 2

    • Using the plastic opening tool, unlock the ribbon cable indicated in the picture by prying up the yellow tab.

    Traducir

  8. Este paso está sin traducir. Ayuda a traducirlo

    : paso 7, imagen 1 de 1

    • Using a plastic opening tool, remove the vibration motor from its housing.

    Traducir

  9. Este paso está sin traducir. Ayuda a traducirlo

    : paso 8, imagen 1 de 1

    • Gently remove the board from the phone using your hand.

    Traducir

  10. Este paso está sin traducir. Ayuda a traducirlo

    : paso 9, imagen 1 de 2 : paso 9, imagen 2 de 2

    • Using the plastic opening tool, gently pry the ribbon cables up as indicated in the pictures.

    Traducir

  11. Este paso está sin traducir. Ayuda a traducirlo

    : paso 10, imagen 1 de 1

    • Carefully remove the battery pack from the phone using your hand.

    • There are fragile tabs on the left and right side of the battery, be careful not to break them off.

    Traducir

  12. Este paso está sin traducir. Ayuda a traducirlo

    : paso 11, imagen 1 de 3 : paso 11, imagen 2 de 3 : paso 11, imagen 3 de 3

    • Carefully insert the metal spudger between the battery and its metal housing and then slowly pry the two apart.

    • Be careful when prying the two apart as to not bend the outer edges of the metal housing because this will make it a lot more difficult to put it back into the phone.

    Traducir
Linea de Meta

83 personas más completaron esta guía.

Autor

con 7 otros colaboradores

Eduardo Nodarse

Miembro Desde 02/10/16

4,797 Reputación

5 Guías creadas

Insignias: 21

+ 18 más insignias

Equipo

USF Tampa, Team 2-5, Sullivan Spring 2016 Miembro de USF Tampa, Team 2-5, Sullivan Spring 2016

USFT-SULLIVAN-S16S2G5

4 Miembros

16 Guías creadas

31 comentarios

Great job with excellent photographs and detailed explanations! Unfortunately this phone is a real goat rodeo when it comes to just replacing a battery. My phone froze and nothing seemed to help unlock it. Fortunately, I went back to an Android site and found the answer and was able to reboot it (holding the on/off button for 10-15 seconds) without trying to remove the battery. Thanks to you I've learned two valuable lessons.

Michael Pobjecky - Contestar

How can i buy the battery for my Zenfone 2 ze550ml .I want 100% original li-po battery.

Skanda - Contestar

my zenfone 2 charging very long time and berry laevel vry sort time discharge

shailendra - Contestar

i replaced my Zenfone 2 ze551ml's battery carefully.

But when i put everything back ,it can not turn on .

the vibration motor is the only thing working

every few minutes the vibration will vibrate two times itself.

Can anyone tell me how to solve this problem,thanks

angus - Contestar

Hi there I'm having the same problem with my phone, did you get any responses on how to fix the problem

mcummings197023 -

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 14

Ultimos 30 días: 91

Todo El Tiempo: 86,165