Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Tienda

Introducción

Use this guide to replace the front-facing camera board on your Asus Transformer T100.

Partes

No se especificaron partes.

  1. Separate the tablet from the base by pressing the large silver button below the tablet. The silver button is located at the base of the tablet. Remove the tablet by lifting up.
    • Separate the tablet from the base by pressing the large silver button below the tablet. The silver button is located at the base of the tablet.

    • Remove the tablet by lifting up.

  2. Insert the opening tool into the seam of the tablet casing and gently pry upwards. With a little force, you will feel the clips release.
    • Insert the opening tool into the seam of the tablet casing and gently pry upwards.

    • With a little force, you will feel the clips release.

  3. Slide the tool along all four edges of the tablet, making sure that all the clips are released.
    • Slide the tool along all four edges of the tablet, making sure that all the clips are released.

    • Do not break these clips; otherwise, the screen will become less secure.

  4. El kit de herramientas esencial

    Las herramientas más útiles en nuestro kit más compacto.

    Compra ahora

    El kit de herramientas esencial

    Las herramientas más útiles en nuestro kit más compacto.

    Compra ahora
  5. Remove the rear casing. Remove the rear casing.
    • Remove the rear casing.

  6. The camera board is located in the red square in this image.
    • The camera board is located in the red square in this image.

  7. Remove the two screws on the camera board using a Phillips #1 Screwdriver. Remove the two screws on the camera board using a Phillips #1 Screwdriver.
    • Remove the two screws on the camera board using a Phillips #1 Screwdriver.

  8. Lift up the power button cable retention clip on the motherboard and pull the cable out. Lift up the power button cable retention clip on the motherboard and pull the cable out. Lift up the power button cable retention clip on the motherboard and pull the cable out.
    • Lift up the power button cable retention clip on the motherboard and pull the cable out.

  9. On the camera connection apparatus, locate the silver tape that connects to the tablet. Peel the silver tape off of the tablet on both sides of the connection apparatus.
    • On the camera connection apparatus, locate the silver tape that connects to the tablet.

    • Peel the silver tape off of the tablet on both sides of the connection apparatus.

    • If this step has been completed correctly, the camera board should be loose, with the tape still attached to the connection apparatus.

  10. Gently pull the Orange ribbon cable  out of the connection port. This port has no clip. The orange apparatus should slide out with a small tug. This port has no clip. The orange apparatus should slide out with a small tug.
    • Gently pull the Orange ribbon cable out of the connection port.

    • This port has no clip. The orange apparatus should slide out with a small tug.

Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

Taylor Pantiga

Miembro Desde 14/04/14

1,520 Reputación

6 Guías creadas

Equipo

Cal Poly, Team 13-31, Maness Spring 2014 Miembro de Cal Poly, Team 13-31, Maness Spring 2014

CPSU-MANESS-S14S13G31

3 Miembros

6 Guías creadas

Hello, can you please tell a manufacturer of the camera (is it writter somethere on it)?

Alexius Hoopakele Ae - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 4

Ultimos 30 días: 13

Todo El Tiempo: 3,288