Menú

Tus configuraciones

Mi Mesa de Trabajo

Obtén acceso rápido a guías, partes y respuestas para tus dispositivos
Mi Carrito

Al parecer tu carrito está vacío

Visita Nuestra Tienda

Asus ROG G751JT-DH72 RAM Replacement

Escrito Por: Anum Haidari (y otro participante)
  • Comentarios: 0
  • Favoritos: 0

Dificultad

Moderar

Pasos

12

Tiempo Requerido

30 minutos

Secciones

1

Banderas

0

Introducción

Use this guide to replace the RAM in your device.

Herramientas

Comprar estas herramientas

Partes

No se especificaron partes.

  1. Lift up the rubber tab located in the upper-right corner of the backing plate. Lift up the rubber tab located in the upper-right corner of the backing plate.

    • Lift up the rubber tab located in the upper-right corner of the backing plate.

    Traducir

  2. Use a Phillips #1 screwdriver to remove the 5.2 mm screw behind the rubber tap.

    • Use a Phillips #1 screwdriver to remove the 5.2 mm screw behind the rubber tap.

    Traducir

  3. Carefully pull the backing plate off. If you have a pry tool, you can pry on the edges carefully.

    • Carefully pull the backing plate off. If you have a pry tool, you can pry on the edges carefully.

    Traducir

  4. Use a Phillips #1 screwdriver to remove the 5mm screw on the right side.

    • Use a Phillips #1 screwdriver to remove the 5mm screw on the right side.

    Traducir

  5. Skip the upgrade.

    Descuento de $10 en tu factura de $50 con
    SKIPANDSAVE10

    Save Now

    Skip the upgrade.

    Take $10 off $50 with
    SKIPANDSAVE10

    Save Now

  6. Pull out the optical drive to revel the screws holding the laptop cover.

    • Pull out the optical drive to revel the screws holding the laptop cover.

    Traducir

  7. Remove all 10 5.2mm Phillips screws holding the main back cover using the Phillips #1 screwdriver. Remove all 10 5.2mm Phillips screws holding the main back cover using the Phillips #1 screwdriver.

    • Remove all 10 5.2mm Phillips screws holding the main back cover using the Phillips #1 screwdriver.

    Traducir

  8. Remove the four 5.2mm screws directly behind the backing plate using the Phillips #1 screwdriver.

    • Remove the four 5.2mm screws directly behind the backing plate using the Phillips #1 screwdriver.

    Traducir

  9. Flip over the laptop and pry the 2 vent covers off.

    • Flip over the laptop and pry the 2 vent covers off.

    Traducir

  10. Remove the two 6.8mm Phillips screws directly below the vent covers using the Phillips #1 screwdriver.

    • Remove the two 6.8mm Phillips screws directly below the vent covers using the Phillips #1 screwdriver.

    Traducir

  11. Pry along the edges of the keyboard to lift it up. Be careful not to damage the ribbon connectors.

    • Pry along the edges of the keyboard to lift it up.

    • Be careful not to damage the ribbon connectors.

    Traducir

  12. Disconnect all 4 ribbon connectors with a tweezer. Disconnect all 4 ribbon connectors with a tweezer.

    • Disconnect all 4 ribbon connectors with a tweezer.

    Traducir

  13. Carefully, pull on the side tabs to release the RAM card.

    • Carefully, pull on the side tabs to release the RAM card.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 1 otro colaborador

Anum Haidari

Miembro Desde 22/10/18

533 Reputación

3 Guías creadas

Insignias: 5

+ 2 más insignias

Equipo

UC Davis, Team S7-G4, Lore Fall 2018 Miembro de UC Davis, Team S7-G4, Lore Fall 2018

UCD-LORE-F18S7G4

2 Miembros

3 Guías creadas

0 Comentarios

Agregar un comentario

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 6

Todo El Tiempo: 130