Introducción

Esta roto el vidrio de tu Apple Watch? Es tiempo de repararlo. Sigue la siguiente guía para reemplazar la pantalla-la cual incluye la pantalla OLED y el digitalizador (táctil).

Como una precaución contra el daño de tu equipo, inicia esta guía desconectando tu bateria, de la unica manera que puedes-quitandola.

Estate seguro de seguir nuestra guía[guia|41083] cuando hayas terminado.

Resumen del Video

  1. Te recomendamos que limpies tu microondas antes de continuar, ya que cualquier suciedad desagradable en la parte inferior puede terminar pegado a el iOpener. Coloca el iOpener en el centro del microondas.
    • Te recomendamos que limpies tu microondas antes de continuar, ya que cualquier suciedad desagradable en la parte inferior puede terminar pegado a el iOpener.

    • Coloca el iOpener en el centro del microondas.

    • Para microondas giratorios: Asegúrate de que la placa gira libremente. Si el iOpener se queda atascado, puede sobrecalentarse y quemarse.

    which temperature must be used for heating? Thx

    fbarletta - Contestar

    I found you need to be very patient when using the iOpener. It's worth taking your time, giving the heat time to work on the glue. When I finally got the battery out, there were some strips of glue left behind that I just cleaned off with some isopropanol before installing the new battery.

    By the way, I had to run the iOpener for longer in my microwave for it to get hot enough. When it was too hot to touch, I figured it was hot enough for the batteries.

    Fredrik -

    I didn't find this to be as hard as I had built it up in my mind to be; HOWEVER, saying that I need to say years ago I was the local Nokia service center in my town. But many years ago right after they got rid of analog times. Yeah. A classic installer/repairer mistake when starting something they haven't fixed or installed before is picking up the instructions, flipping through them; maybe even reading a section that is new-then tossing the instructions over the shoulder. "I got this." This usually comes right before something major gets broke. And I can tell you when you try to do it yourself and then mess it up horribly then take it to the repair shop. Well we called that "I can do it myself" syndrome and charged extra to put back together what they brought in in the box. Now knowing all this - I can't stress this enough because I am stupid, stupid, stupid. COVER YOUR SCREEN IN CLEAR BOXING TAPE AND READ ALL THE INSTRUCTION BELOW THROUGH TO THE END BEFORE EVEN ATTEMPTING THIS FIX. Take my advise.

    windizy - Contestar

    I didn't have an iOpener, so I used a wheat type heat bag. If you do this though, make sure you put a layer of plastic between your Mac and the bag, or you'll get condensation in places you don't want it.

    Martin Gray - Contestar

    I started out using the iOpener but switched to my wife's hairdryer. A heat gun or hair dryer proved to be much more convenient and is a time saviour. You can heat more and the glue becomes more fluid make the next steps with the opening picks much easier

    Jan Van Puymbroeck - Contestar

    Use a hair dryer! Watch this vid: https://youtu.be/16GkvjVyOJA It is much easier to do if you heat it from the other side.

    Fletcher Carpenter - Contestar

    I wonder how many people actually wrapped in their iPhone into iOpener and put this "sandwich" into microwave??

    putinaspiliponis - Contestar

    I know this is obvious, but backup your iPad with iTunes before you start. I'd also turn off your passcode if you have one.

    Laurie Higgins - Contestar

    Ther first time you heat up the iOpener for this repair when its room temperature I had to heat it up for more than 30 seconds. I remember I had to heat it up for around 45 seconds. However, after that when you need to reheat it again during the repair 30 seconds will be enough.

    Yousef Ghalib - Contestar

    I've been with Samsung for 8 years now!! Never did i have a case on any of my phones My Samsung 8 is 2 months old the case protector around the edge pop off and broke my phone it's like someone put a bullet hole in it

    Sherry Carew - Contestar

    Not everybody has a microwave. You need to state how long and at what temperature in a conventional oven.

    Esmond Pitt - Contestar

    Hi, the microware have multiple power 1 to 9, what must be used ?

    Regards,

    Cedric

    Cedric VINCENT - Contestar

    My microwave just died, can i heat it with boiled water?

    Alex COLOMBANI - Contestar

  2. Calienta el  iOpener durante treinta segundos.
    • Calienta el iOpener durante treinta segundos.

    • A lo largo del procedimiento de reparación, en cuanto el iOpener se enfríe, vuelve a calentarlo en el microondas treinta segundos más cada vez.

    • Ten cuidado de no sobrecalentar el iOpener durante la reparación. El sobrecalentamiento puede provocar que el iOpener se rompa.

    • Nunca toques el iOpener si parece estar hinchado.

    • Si el iOpener esta todavía demasiado caliente al tacto, sigue utilizándolo mientras esperas a que se enfríe un poco más antes de recalentar. Un iOpener adecuadamente climatizado debe mantenerse caliente durante un máximo de 10 minutos.

    May I know the temperate limit about heating iOpener? (maximum 150 degrees Celsius?) thx so much.

    yamayhuang - Contestar

    I had to heat mine up for more than 30 seconds. After 30 seconds on high it was only warm. It had to keep trying different times and checking it until it got hot. I think the initial time that I put it in for was over a minute.

    whale13 - Contestar

    DO NOT USE IN NON ROTATING MICROWAVE! It will pop a hole. I had it in for 45 seconds the first time. It wasn't very hot inside and I saw it started to leak on the paper towel I put under it. Just a fair bit of advice. I think I will just stick with the heat gun. Loud but useful.

    Alex Jackson - Contestar

    I don't own a microwave.

    mdanihy - Contestar

    Its again waterproof when you change iphone 7 battery?

    Jon - Contestar

    I don't have a microwave???

    Joe Blow - Contestar

    30 sec at which equivalent watts setting and what temperature does iOpener heats up to for 30 secs. Only just bought it so needs info before using it. Thanks

    Sam Stieg - Contestar

    can i use just ordinary microwave???

    juneseok kwon - Contestar

    If I don't have a microwave then I try to use hot air gun so how many munuts i want to heat ?

    Mohideen Rifay - Contestar

    I heated mine up for 30 seconds, tested, then again for 30 seconds. It felt adequately hot. Leaving it on the left side, per the instruction, for a minute did not loosen the adhesive. I ended up pulling the suction cup hard enough to shadder the old screen. Moral of the story, I don't think it gets hot enough safely to have an affect.

    Travis Dixon - Contestar

    There is a clear problem here with the heating part using the iopener things....no details are given. Whoever is testing them needs to make it clear - What temperature does it need to be? And for which phone models, because they differ in what's needed. It's only £10-15 for a laser guided temp sensor unit, and the designers/repairers should have one of those already for doing these kinds of repairs. Explaining half a repair, is worse than not explaining at all :-(

    assortedrubbish - Contestar

    I used a hot water bottle, works well as it covers the whole screen and stays hot for longer.

    dave - Contestar

    If I may suggest include your microwave wattage so people can get an idea on time for there own

    Patrick Storey - Contestar

    I ended up using a hair dryer. That iOpener thing took forever.

    mark fitzgerald - Contestar

    30 seconds sure isn’t cutting it… 45 didn’t get the screen of my iPad air 2 to budge either… even after resting on the ipad for 4 minutes.

    60 seconds in the microwave, the iOpener burst.

    I’ll get a new one and try once more with heating it 45 seconds and repeat that for 30 minutes like others have said here. If that doesn’t work it’ll have to be the heat gun.

    K

    Karl Marble - Contestar

    I can’t recommend the microwave. If the the iOpener becomes too hot, it bursts. Better put the opener in cooking water. Dry it and use it. Instead of an iOpener you can use hot/cool packs as well.

    Bernhard Keim - Contestar

    Trust the directions! I forgot and left it in the Microwave too long and after 1 minute I had Mt Vesuvius - the iOpener burst and spewed the goodies out. The problem is, the Digitizer can be damaged by a hot air gun, so I had to tough out and remove the glue the hard way. I made it … with lots of patience! Tough lesson.

    Larry Bennett - Contestar

  3. Saca el iOpener del microondas, cogiéndolo por una de las esquinas planas para evitar el centro caliente.
    • Saca el iOpener del microondas, cogiéndolo por una de las esquinas planas para evitar el centro caliente.

    • El iOpener estará muy caliente, ten cuidado cuando lo manipules. Utiliza guantes de horno si es necesario.

    Will a hair dryer work for heating the glass?

    Me berg - Contestar

    Yes, as does a heat gun.

    anonymous 4602 - Contestar

    I did this repair. I used a hair dryer, I think it works better: gets very hot fast.

    Cobus de Beer - Contestar

  4. Coloca el iOpener acalorado en la caratula del reloj.
    • Coloca el iOpener acalorado en la caratula del reloj.

    • Deja el iOpener en la caratula por lo menos un minuto para calentar la pantalla y ablandar el adhesivo asegurandola a la caja.

    • Quizás tendrás que recalentar el iOpener o moverlo alrededor de la pantalla mientras las secciones se enfríen, para calentar la pantalla lo suficiente para despegarla.

  5. Debido al espacio entre la pantalla y la caja del reloj es tan delgada, una cuchilla es requerida para separar los dos. Lee los siguientes avisos cuidadosamente antes de proceder.
    • Debido al espacio entre la pantalla y la caja del reloj es tan delgada, una cuchilla es requerida para separar los dos. Lee los siguientes avisos cuidadosamente antes de proceder.

    • Siempre mantén tus dedos completamente apartados de la cuchilla.

    • Ten cuidado de no aplicar mucha presión, ya que esto puede causar que se deslice la cuchilla y te puede cortar o dañar el reloj.

    • Ponte protección ocular. La cuchilla o el vidrio pueden quebrarse, enviando pedazos al aire.

  6. Utilizando una cuchilla curvada minimiza la probabilidad de rasgunar la caja o de quebrar el vidrio. Solo haz palanca con la seccion Coloca la sección curvada de la cuchilla en el espacio entre el vidrio y la caja en la esquina inferior de la caratula, y presiona firmemente hacia el espacio. Ten mucho cuidado de mantener control completo sobre la cuchilla—media vez el espacio se abre, si estas presionando la cuchilla muy fuerte se puede deslizar y cortar la batería.
    • Utilizando una cuchilla curvada minimiza la probabilidad de rasgunar la caja o de quebrar el vidrio. Solo haz palanca con la seccion

    • Coloca la sección curvada de la cuchilla en el espacio entre el vidrio y la caja en la esquina inferior de la caratula, y presiona firmemente hacia el espacio.

    • Ten mucho cuidado de mantener control completo sobre la cuchilla—media vez el espacio se abre, si estas presionando la cuchilla muy fuerte se puede deslizar y cortar la batería.

    • Esto debe de abrir el espacio y causar que el vidrio se levante un poco de la caja.

    • Cuando el vidrio se haya levantado, cuidadosamente gira la cuchilla hacia abajo, abriendo el espacio mas por medio del levantamiento del vidrio.

    It is not possible to separate the screen from the casing? I have heated this thing numerous times and the opening is way too small to get any type of blade, knife or other tool in between. Any suggestions???

    Paul - Contestar

    Using a curved blade like the guide recommends, angle the blade straight down between the glass and the edge of the frame, mid-way along the bottom edge of the case. The metal of the case will flex *just a little bit*, allowing you to slowly rotate the blade so the cutting edge is now pointing towards the center of the watch instead of down towards your work surface. You may need to rock the blade back and forth, sort of massaging the curve into the seam between the glass and the metal before it works. And like they mention above, lots of heat. I used the heatpack they sell, put it in my toaster oven on 200. I started at 130, and went up in 20 degree increments until it worked.

    Pete -

    I've tried everything, heating it up until it's too hot to touch, pressing the knife in the gap straight down, at an angle, nothing seems to work. I've tried using all my arm strength and it still doesn't even enter the gap. Is the iFixit Jimmy not thin enough for the job?

    Kenneth - Contestar

  7. Media vez hayas abierto el espacio lo suficiente, inserta la punta de una púa debajo del vidrio. Desliza la pua a lo largo del borde inferior para separar el adhesivo asegurando la pantalla a la caja. Ten cuidado de no insertar la púa demasiado adentro. Solo 1/8" (como 3 mm) es necesario, mas profundo y puedes dañar los cables.
    • Media vez hayas abierto el espacio lo suficiente, inserta la punta de una púa debajo del vidrio.

    • Desliza la pua a lo largo del borde inferior para separar el adhesivo asegurando la pantalla a la caja.

    • Ten cuidado de no insertar la púa demasiado adentro. Solo 1/8" (como 3 mm) es necesario, mas profundo y puedes dañar los cables.

  8. Rueda la pua hacia el lado del reloj, por el lado del boton, cuidadosamente empujando hacia adentro para separar el adhesivo y agrandar el espacio. Acuérdate de no empujar la púa demasiado hacia adentro—es mas fácil de evitar esto rodando la púa en vez de arrastrar hacia alrededor. Acuérdate de no empujar la púa demasiado hacia adentro—es mas fácil de evitar esto rodando la púa en vez de arrastrar hacia alrededor.
    • Rueda la pua hacia el lado del reloj, por el lado del boton, cuidadosamente empujando hacia adentro para separar el adhesivo y agrandar el espacio.

    • Acuérdate de no empujar la púa demasiado hacia adentro—es mas fácil de evitar esto rodando la púa en vez de arrastrar hacia alrededor.

  9. ¡Envío gratuito para todos los pedidos de más de USD100 o que contengan un Pro Tech Toolkit!

    Visita Nuestra Tienda
  10. Desliza la pua hacia alrededor de la esquina derecha superior, y rueda la hacia alrededor del borde superior de la pantalla. Desliza la pua hacia alrededor de la esquina derecha superior, y rueda la hacia alrededor del borde superior de la pantalla. Desliza la pua hacia alrededor de la esquina derecha superior, y rueda la hacia alrededor del borde superior de la pantalla.
    • Desliza la pua hacia alrededor de la esquina derecha superior, y rueda la hacia alrededor del borde superior de la pantalla.

  11. Continua deslizando la pua hacia alrededor del perímetro de la pantalla, rodando hacia el lado izquierdo para cortar lo ultimo del adhesivo. Deja la púa en su lugar para prevenir que la pantalla se vuelva a pegar a la caja. Deja la púa en su lugar para prevenir que la pantalla se vuelva a pegar a la caja.
    • Continua deslizando la pua hacia alrededor del perímetro de la pantalla, rodando hacia el lado izquierdo para cortar lo ultimo del adhesivo.

    • Deja la púa en su lugar para prevenir que la pantalla se vuelva a pegar a la caja.

  12. Mientras detienes la primer púa en su lugar, utiliza una segunda púa para revisar que todo el adhesivo este separado alrededor del perímetro completo de la pantalla. Mientras detienes la primer púa en su lugar, utiliza una segunda púa para revisar que todo el adhesivo este separado alrededor del perímetro completo de la pantalla. Mientras detienes la primer púa en su lugar, utiliza una segunda púa para revisar que todo el adhesivo este separado alrededor del perímetro completo de la pantalla.
    • Mientras detienes la primer púa en su lugar, utiliza una segunda púa para revisar que todo el adhesivo este separado alrededor del perímetro completo de la pantalla.

  13. Hay dos cables conectando la pantalla al interior del reloj, cerca de la esquina superior izquierda. Ten cuidado cuando hagas palanca o puedes dañar estos cables. Ligeramente haz palanca en el lado derecho de la pantalla, para liberarla de cualquier adhesivo restante. Haz palanca en la izquierda para liberar lo también—pero no intentes de remover la pantalla ya que esta detenida en su lugar por dos cables.
    • Hay dos cables conectando la pantalla al interior del reloj, cerca de la esquina superior izquierda. Ten cuidado cuando hagas palanca o puedes dañar estos cables.

    • Ligeramente haz palanca en el lado derecho de la pantalla, para liberarla de cualquier adhesivo restante.

    • Haz palanca en la izquierda para liberar lo también—pero no intentes de remover la pantalla ya que esta detenida en su lugar por dos cables.

  14. Si puedes ver la capa superior de tu sensor de Force Touch entre el adhesivo de pantalla, significa que las dos capas del sensor esta separadas y tendrás que reemplazarlas o repararlas. La capa superior del sensor puede estar pegada al lado reverso de la pantalla—empujalo hacia abajo para separarlo y cambia hacia nuestra guia de Sensor de Force Touch a partir de aqui. La capa superior del sensor puede estar pegada al lado reverso de la pantalla—empujalo hacia abajo para separarlo y cambia hacia nuestra guia de Sensor de Force Touch a partir de aqui.
    • Si puedes ver la capa superior de tu sensor de Force Touch entre el adhesivo de pantalla, significa que las dos capas del sensor esta separadas y tendrás que reemplazarlas o repararlas.

    • La capa superior del sensor puede estar pegada al lado reverso de la pantalla—empujalo hacia abajo para separarlo y cambia hacia nuestra guia de Sensor de Force Touch a partir de aqui.

  15. Levanta la pantalla hacia arriba y mueve la pantalla hacia la izquierda, prestando atención a los cables de datos de pantalla y digitalizador. Levanta la pantalla hacia arriba y mueve la pantalla hacia la izquierda, prestando atención a los cables de datos de pantalla y digitalizador. Levanta la pantalla hacia arriba y mueve la pantalla hacia la izquierda, prestando atención a los cables de datos de pantalla y digitalizador.
    • Levanta la pantalla hacia arriba y mueve la pantalla hacia la izquierda, prestando atención a los cables de datos de pantalla y digitalizador.

  16. Coloca el reloj en una superficie elevada, por lo menos 1/2" o 1 cm de altura—una caja pequeña o el borde de un libro funcionara perfectamente. Esto permitirá que la pantalla se cuelgue hacia abajo verticalmente y dará mejor acceso a la batería.
    • Coloca el reloj en una superficie elevada, por lo menos 1/2" o 1 cm de altura—una caja pequeña o el borde de un libro funcionara perfectamente. Esto permitirá que la pantalla se cuelgue hacia abajo verticalmente y dará mejor acceso a la batería.

    • Ten cuidado de no golpear la pantalla o esforzar los cables mientras trabajas.

  17. Inserta una herramienta de apertura plastica entre el lado derecho de la bateria y la caja. Haz palanca contra la batería para separarla del adhesivo asegurándola a la placa del sistema. No intentes de remover la batería ya que aun esta conectada.
    • Inserta una herramienta de apertura plastica entre el lado derecho de la bateria y la caja.

    • Haz palanca contra la batería para separarla del adhesivo asegurándola a la placa del sistema.

    • No intentes de remover la batería ya que aun esta conectada.

    I tried removing the battery with the prying tool as instructed, but I think it may have slightly damaged the outer black plastic wrapping of the battery. Does this mean the battery is now damaged and needs to be replaced? Or is that just a cover around the battery and it doesn’t matter? I just don’t want any battery chemicals leaking out. Asking before I stick the screen back on the watch, I’ve done all the rest and it seems fine otherwise.

    Danae - Contestar

    Hi Danae, the black plastic is technically just protective, but I would highly recommend replacing the battery. It’s possible there is additional unseen damage, and that plastic helps protect against swelling and normal wear of the battery inside the device.

    Sam Lionheart -

  18. Gira la batería en sentido contrario a las agujas del reloj para exponer el conector. Gira la batería en sentido contrario a las agujas del reloj para exponer el conector.
    • Gira la batería en sentido contrario a las agujas del reloj para exponer el conector.

  19. Agarra la batería hacia arriba y fuera del camino para exponer el conector del cable de la batería. Utiliza una herramienta plástica de apertura contra el inferior de la caja para separar el conector del cable de la batería del cable de la batería del reloj. Saca la batería fuera del reloj.
    • Agarra la batería hacia arriba y fuera del camino para exponer el conector del cable de la batería.

    • Utiliza una herramienta plástica de apertura contra el inferior de la caja para separar el conector del cable de la batería del cable de la batería del reloj.

    • Saca la batería fuera del reloj.

    Why should you remove the battery if you only need to replace the screen?...?

    Douglas Richey - Contestar

    Douglas - this iFixit is for Apple Watch Battery Replacement - looks like you need to remove the screen to replace the battery...

    jimvaughn6 - Contestar

    You will find that it is a good precautionary measure to disconnect the battery anytime you are repairing or replacing a screen as a short can occur when reconnecting the screen rendering it useless even if you have the unit turned off.

    Bryan Solo - Contestar

    Great repair guide! You iFixit guys are awesome. Took me about 2 hours but then I am very careful and I replaced the touch sensor at the same time since I had it open anyway. Make sure you have at least 2, and better 3 adhesive gaskets. You need 2 and, well, it’s easy to mess one up while trying to place it.

    rbolling - Contestar

    Will removing the battery reset my icloud info? I have a guy who says he can do this, but i dont want him to run off with my watch after he replaces the battery…

    dreadmusicreview - Contestar

  20. Dobla la pantalla hacia la derecha, para exponer los cables debajo de ella. Dobla la pantalla hacia la derecha, para exponer los cables debajo de ella. Dobla la pantalla hacia la derecha, para exponer los cables debajo de ella.
    • Dobla la pantalla hacia la derecha, para exponer los cables debajo de ella.

  21. Los conectores del cable de la pantalla y del digitalizador están asegurados debajo de un pequeño soporte metálico adherido al altavoz. Utilice una herramienta de apertura de plástico para voltear el soporte hacia la pantalla y hacia arriba desde el altavoz. Si simplemente haces palanca hacia la banda del reloj es posible romper los cables.
    • Los conectores del cable de la pantalla y del digitalizador están asegurados debajo de un pequeño soporte metálico adherido al altavoz.

    • Utilice una herramienta de apertura de plástico para voltear el soporte hacia la pantalla y hacia arriba desde el altavoz.

    • Si simplemente haces palanca hacia la banda del reloj es posible romper los cables.

  22. El soporte que contiene las conexiones del cable de la pantalla y del digitalizador está compuesto por una pieza superior e inferior. Los conectores están asegurados a la parte inferior, y la parte superior debe ser retirada para desconectarlos. Use pinzas de punta fina para agarrar la mitad inferior del soporte. Hay una pequeña lengüeta de metal que sobresale hacia abajo desde el soporte metálico superior.
    • El soporte que contiene las conexiones del cable de la pantalla y del digitalizador está compuesto por una pieza superior e inferior. Los conectores están asegurados a la parte inferior, y la parte superior debe ser retirada para desconectarlos.

    • Use pinzas de punta fina para agarrar la mitad inferior del soporte.

    • Hay una pequeña lengüeta de metal que sobresale hacia abajo desde el soporte metálico superior.

    • Inserte un destornillador de cabeza plana pequeño (1 mm) entre la lengüeta y el soporte inferior y gire el destornillador para separar el espacio.

    • Esto liberará dos lengüetas que sujetan el soporte superior a la inferior y deben liberar el soporte superior.

    I was really careful at this step but damaged the connectors inside. I would not advise the above method of separation and thin this should be reviewed. Your video is also misleading as to how "easy" it is to separate these two plates. Please review this.

    Brent - Contestar

    Brent, how did you realized that inner connector was damaged?

    Ivan Sorkin -

    I agree with Brent. Your instructions are not very clear about how to get the bracket apart. I also damaged one of the pop connectors. Your picture shows the tweezers inside between the upper and lower part of the bracket. If you are not careful that will damage the pop connector on that side which is exactly what I did. If you can get something on the tiny tab on the unhinged side of the bracket and slightly pry it apart the bracket will come right apart.

    Douglas Richey - Contestar

    Also agree: a little too much pressure and the ribbon cable tears at the point it enters the bracket. Take it SLOW and make sure you have really good light and vision. Orient yourself.

    Dave Varon - Contestar

    And this is where things went south for me too. Ended up disconnecting from the rest of the watch and the Taptic Engine. I read through this and watched this portion of Ifixit’s YouTube video no less than 15 times, so confusing they way it’s worded and the pictures didn’t help. Now I’m out of luck and out of $190.

    Timothy Hipps - Contestar

    I also damaged the ribbon following this direction. Tweezers can not be inserted between the the clip body. Seems to me a different tool is needed to release the the hinge clasp where the the screw driver blade is used?

    guy gagne - Contestar

    Pas de problèmes me particulier à cette étape. Le fait de pousser très légèrement sur la petite languette qui dépasse a suffit, il n’y a vraiment pas besoin de forcer.

    Raphaël WOLFF - Contestar

    Solution I have come up with is to hold the bracket between your thumb and index finger and insert a flathead under the little tab on the right side. This way, the tab still unlatches, but it only moves slightly. Your cables should be safer then.

    Alec Thompson - Contestar

  23. La mitad superior del soporte del conector de la pantalla se mantiene en el extremo superior mediante una lengüeta metálica que encaja en una ranura en el soporte inferior. Agarre el soporte superior con sus pinzas y deslícelo hacia la parte superior del reloj para desenganchar esta pestaña y libere el soporte. Agarre el soporte superior con sus pinzas y deslícelo hacia la parte superior del reloj para desenganchar esta pestaña y libere el soporte.
    • La mitad superior del soporte del conector de la pantalla se mantiene en el extremo superior mediante una lengüeta metálica que encaja en una ranura en el soporte inferior.

    • Agarre el soporte superior con sus pinzas y deslícelo hacia la parte superior del reloj para desenganchar esta pestaña y libere el soporte.

  24. Desconecte la pantalla de datos y los cables del digitalizador. Tenga cuidado de no tocar ninguno de los contactos directamente, ya que los aceites de los dedos pueden impedir la conectividad.
    • Desconecte la pantalla de datos y los cables del digitalizador.

    • Tenga cuidado de no tocar ninguno de los contactos directamente, ya que los aceites de los dedos pueden impedir la conectividad.

    • Retire la pantalla.

    So how do you get the display off the screen or did I already mess it up cause I just did it

    Jamie Groff - Contestar

    Hello guys , appreciate the effort that u guys are doing , have one question though , I own a series 2 watch and I was thinking about changing my screen caz is cracked but I can't find that many lcd for 2 series , and now my question Would a 1 series lcd match my 2series watch? Keep on searching but no answers!!! Many thanks

    cris cri - Contestar

    Great repair guide! You iFixit guys are awesome. Took me about 2 hours but then I am very careful and I replaced the touch sensor and the battery at the same time since I had it open anyway. Make sure you have at least 2, and better 3 adhesive gaskets. You need 2 and, well, it’s easy to mess one up while trying to place it.

    rbolling - Contestar

    I followed the above instructions and successfully replaced the broken screen, however the new screen won’t pair to my iphone or fully boot up, only goes to a certain point (Pairing stage) and then starts over; any suggestions on what the problem could be?

    Gregg Hardy - Contestar

    The display bracket that holds the 2 display connections is the most difficult part of this procedure. (Once you get the display off). A bit clearer explanation would be helpful (or a diagram of where you are actually putting the 1mm flathead and then twisting.

    jeff53 - Contestar

Conclusión

"Para reensamblar tu equipo, sigue nuestra Apple Watch Adhesive Replacement guía."

182 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

Equipo

iFixit Miembro de iFixit

Community

108 Miembros

8,330 Guías creadas

Does anyone know if I can replace my glass display for the saphier one??

dracospitfire - Contestar

Yes, they are cross compatible. Look under features at Apple Watch (42 mm, Original & Series 1) Screen and Digitizer

Arthur Larin -

First of all WHERE CAN WE BUY A OEM GENUINE AUTHENTIC APPLE GLASS REPLACEMENT?

My question is if Apple doesnt sell oem genuine ones who will?

gleeglee217 - Contestar

How much do the respective Sapphire and Gorilla Glass displays weigh by themselves?

Mac 128 - Contestar

There are replacement touch screen/digitizer available on eBay. But the question is how do you separate the OLED display from your damaged touch screen to just replace the glass?

dotbear040306 - Contestar

Exactly. thats what ifixit sells, they should have a guide for it.

Andrew spoelstra -

I found a video in German that shows this. I can't believe this iFixit guide fails to go into the crucial steps of the repair it's supposed to be about! Beware, this is not something a home hobbyist is going to be able to do. I got most of the way through my repair before I came across this german vid, and now I'm going to try to source a complete glass+LCD unit. Separating the LCD from the glass is hard enough, but you need special equipment to bond the old LCD to the new glass, and there's a good chance the two won't talk to each other anyway, based on the comments below.

https://www.youtube.com/watch?v=LvWPfUhp...

Pete -

That’s simply not possible, as they’re laminated insanely close together. You kind of have to replace the OLED too, as they’re permanently bonded together.

Liam Powell -

Can somebody help me with links or numbers from where I can buy the display for my Apple Watch 42mm. Can't seem to find anywhere.

Ruchit Shah - Contestar

Can somebody help me with website links as to where I can but Apple Watch display 42mm. I have cracked mine and can't find anywhere online to buy the spare part to replace it myself.

Ruchit Shah - Contestar

That looked easy but what if the screen is already cracked?

ron roca - Contestar

hello! how to fix the other side of iwatch. other side i mean where put to charger ???

df - Contestar

Can somebody help me with links or numbers from where I can buy the display for my Apple Watch 42mm. Can't seem to find anywhere.

Mycoal 23 - Contestar

Can I replace Apple Watch stainless steel screen with a screen from aluminum Apple Watch?

Thomas Vartanian - Contestar

Yes, they are cross compatible. Look under features here: Apple Watch (42 mm, Original & Series 1) Screen and Digitizer

Arthur Larin -

You should start a business where as you fix these Apple Watch screens and charge for it. I would gladly pay send my watch to an independent contractor of apple to replace my Apple Watch screen if I could find one.

Gordon Elliott - Contestar

Where can I find someone to replace my 38mm watch screen? Just the screen is cracked, everything else is working fine. Anywhere in Johannesburg?

Alice Yu-Chen Chung - Contestar

Ok I successfully fix my watch screen (glass only had to cut the lcd off and reattach with that loca glue) looks great but the digitizer will not work. I have read on many forms that they are serialized if so can that be fixed if so how? Has anyone successfully repaired an iwatch that works fully?

mike - Contestar

The battery in my watch expanded and ejected the display, unfortunately the display is totally missing. Looks like it is junk now, except for the band?

kklotz - Contestar

Apple now has a recall for this

Tom -

What do you use to "glue" the watch face back down with?

mkk65 - Contestar

I'd like to know this too!

imachunty -

Le tutoriel est pafaitement clair.

1H00 pour realiser cette reparation.

Prévoir un joint fore touch sensor .

youstt - Contestar

Hi, will the screen off a 42mm Series 2 Apple Watch fit, and work, with a 42mm Series 1 watch?

lukecresswell16 - Contestar

Step 21-22 is a lot more difficult than displayed here so be warned! Inside where they advise you to put the tweezer is right up against the connector and any movement of the tweezer in this position will no doubt damage the connector.

There isn't even a warning posted at these steps which is terrible for fixit!!! check the net for other videos on how to get this little box assembled apart - there are far better ways I discovered but too late for me :(

Brent - Contestar

Brent what happened to your watch?

I might have similar problem

Ivan Sorkin -

Trop compliqué :-(

J'ai finalement fait réparé ma montre ici :

https://www.atelierfamilial.fr/reparatio...

Pour moins de 200€, avec une garantie d'un an.

@+

Paul

Paul Vallejo - Contestar

After replacing my Apple Watch screen and digitizer, my battery lasts for 3-4 hours, Digital Crown is not working and hart rate ca't be measured. But the rest works fine, I'm not sure why. Can someone suggest me troubleshooting path?

Ivan Sorkin - Contestar

Some people on the Internet of said that this repair is not possible without losing some functionality, is that true?

rickcostel - Contestar

Is it possible to use a Apple Watch Series 1 LCD and digitizer to replace a cracked screen on the Series 2 model? Thanks!

Charlie Eccher - Contestar

Please i need to know if this is possible too

fikayoogunfuye -

Hi,

Thantk to this guide I’ve succesfully replaced the digitizer on 38mm!

Everything works fine but display is not as bright as it should be.

It is OK during start, the apple logo is bright, then it goes much much darker.

I’ve checked the brightness settings obviously :).

Any idea why it goes darker when finishing booting?

Robert Bonat - Contestar

I would like to get a new screen for my Apple Watch (Series 2) 42mm.

Do you sell it? Or dou you know where can I buy it?

Luis Angel Cerritos - Contestar

Is this the same process for a Series 2? And is the screen the same? I am trying to fix my Series 2 watch. Thank you

Laszlo Rendas - Contestar

I had a company fix my Apple Watch when I got it make it seems darker and isn’t as bright as before I took it in. Any clue as to what could have happened? Please email if u have an idea

Patty Forbush - Contestar

how i can recover glass of lcd by grow or what ?

MOHD - Contestar

Is this screen compatible with Series 3 Apple Watch?

Jai Aenugu - Contestar

Is this compatible with Apple watch series 3?

Jai Aenugu - Contestar

Is this compatible with Apple watch series 3?

Thomas Swainson - Contestar

No… u have to get the one for series 3:-/

nancyphung123 -

I replaced one of these and the screen popped off after they started wearing it. Somehow it didn’t break despite detaching and flinging onto a tile floor, but I still haven’t figure out how to put it back together and be able to trust it. You’d think 300LSE is trustworthy (it is for iPads), but not this time :(

LFB - Contestar

Great guide, but can I just confirm one thing? My series 1 has a cracked screen, but the display including the touch functionality seems to still work perfectly, and the only reason I’m not wearing it since the crack is that there are tiny sharp bits of glass. Given that the touch screen and display seem ok, is it possible to just replace the glass, as opposed to the whole display as per this how-to ?

cheers,

Ian

Ian McIntosh - Contestar

There is, but it is way too complicated… involves using a thin wire to separate the digitiser (touch screen) from the lcd display which is very labour intensive, then using a special laminate, which you can get, but then also you need the industrial machinery to bind them together… this is why even though I have the exact same problem as you I am thinking of replacing the whole screen with lcd. I will post a reply here if/when I am successful!

Danae -

Fait sans difficulté, fonctionne parfaitement.

matthieu.requenna - Contestar

Just updating for anyone wondering if the screen replacement worked. It was successful for me! Followed the steps exactly and it worked :)

Danae - Contestar

I’m still wondering what kind of glue is to be used on the screen

pxolo10 - Contestar

Well thanks for the video. But I Destroy the battery cable while try to hold the cable down to remove the battery…..after that I realized it wasn't realy nesessary to remove the batterie to change the display….So better just leave battery :-/

Mischa Mang - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 449

Últimos 7 Días: 3,117

Últimos 30 Días: 13,825

Todo El Tiempo: 837,978