Introducción
El filtro EMI está instalado en el dispositivo y está detrás de algunos componentes. Debido a esto, hay muchos cables a su alrededor que no forman parte de este componente específico. Asegúrate de seguir cuidadosamente los cables y los componentes para asegurarte de que se extraen las piezas correctas.
Qué necesitas
-
-
Coloca la pantalla con el lado de la pantalla hacia arriba.
-
Coloca las dos ventosas a ambos lados de la parte superior de la pantalla y asegúresate de bloquearlas en su lugar.
-
La pantalla de cristal está conectada al resto de la pantalla mediante pequeños imanes. Levanta lentamente y la pantalla se apagará de inmediato.
-
-
-
Desatornilla los 12 tornillos alrededor de los bordes laterales y la parte superior de la pantalla LCD con el destornillador TR 10.
The screws marked in orange don't need to be removed, all they do is hold the magnets on the LCD.
Yes “orange screws” does not need to be removed.
You do not need a TR10 screwdriver as written in the text a T10 will suffice (more common and also correctly mentioned in the list of tools).
A TR10 screwdriver is compatible with the T10, but not the other way around
Any info on if an older 2011 imac screen could just be plugged into this to replace the current lcd?
-
-
-
Levanta lentamente la pantalla LCD de su ubicación e inclínala hacia arriba.
Add the note that it should be lifted from the bottom edge. It is also important not to twist the display by levering up from one corner.
Before lifting the monitor, you should be prepared to start collecting screws and have your TR 10 ready.
-
-
-
Para el primero de los cuatro cables (el más alejado del cable sujeto por un tornillo), sujeta el conector y tira lentamente.
Note: be sure to pull away but not hard. Wiggle and pull slowly. These are delicate especially due to age.
Overall this is a moderate repair. Follow step by step and you are good.
Also, use tape and/or labels to mark which cables go where per the MLB and other parts. Resulting in easier reassembly.
-
-
-
Para el siguiente conector, que está justo al lado del cable anterior, hay un trozo de cinta pegado a una barra de metal.
-
Voltea la barra de metal usando la cinta como manija.
-
A continuación, sujeta el conector y tira de él lentamente para sacarlo del zócalo de la placa lógica.
What is this connector for?
I imagine this connector is going to be for display data (i.e. LCD data).
I pretty much mangled this cable trying to put it back into the slot. Is this something I can order a replacement for?
Thunderbolt Display 27" LVDS Cable
As other’s have said, this cable is super delicate.
When you replace it, make sure that the small metal handle it firmly reattached to the other side of the port. I thought I’d got it right first time, but had no video signal (thunderbolt detected display, and power was fed to the Macbook Pro).
I had to reinsert this one again, and one in, firmly press the connector home, then latch the handle over the other side. I also gave it a test pull to ensure it was secure. Then all was well!
Can anyone provide a photo of this connector so as to give a better understanding of its mechanics? see this cringe worthy effort at guidance; https://youtu.be/A96CUSm_Xhs?t=1050
-
-
-
-
Para el conector del otro lado de la placa lógica, toma el conector por debajo y tira con cuidado de la placa.
This cable was also taped for me, so remove the tape first
-
-
-
¡La pantalla LCD ahora se ha desconectado por completo de la carcasa y se puede reparar/reemplazar!
-
-
-
Ahora deberías ver el filtro EMI justo en el medio del dispositivo (aunque retenido por algunos otros componentes).
-
Sigue los cables que salen de la parte inferior del adaptador de corriente hacia la izquierda.
-
Toma las pinzas y retira el trozo de cinta que sujeta los cables a la carcasa.
-
Solo hay un conector que debe sacarse (¡aunque hay dos uno al lado del otro!).
-
Agarra el conector por la parte inferior y sácalo con cuidado de su toma correspondiente.
Yes - pictures and last bullet point are misleading and confusing respectively. I suggest fixit should remove the second picture and replace it with a picture of the connector that should be removed and amend the last bullet point o read something like 'depress the clip that holds the left connector in place and carefully etc ...'
Avoid the verb 'grab'
Yes, grab has no finesse at all. Grabbing and ripping are what makes the whole process a potential nightmare :)
-
-
-
El componente del altavoz circundante (la caja negra) alrededor de la entrada de alimentación debe quitarse.
-
Utiliza el destornillador TR 10 para quitar los cuatro tornillos.
-
Desconecta el altavoz de detrás de la placa lógica tirando con cuidado del extremo de plástico del cable.
-
Retira el altavoz.
If you are only replacing the Thunderbolt and MagSafe cable, steps 11-13 do not need to be performed ie speaker and EMI filter do not need to be removed, only the screw holding the grounding cable on the EMI filter (top left of round disk).
I concurr with M Baynes.
-
-
-
Ahora que el altavoz del medio está fuera del camino, se puede acceder fácilmente al filtro EMI.
-
Con unas pinzas, retira la cinta plateada que se encuentra en la parte superior del filtro.
I can’t help but notice that this assembly that is called an EMI (Electromagnetic Interference) Filter is in the exact position that my monitor has been displaying a band of disrupted color bands once it heats up. I am changing the Thunderbolt cable assembly in hopes that is fixes the problem. If it doesn’t then I will make changing the Filter my next quest. It is also noteworthy that the Filter is grounded to the case by the metal tape which must be peeled back for this procedure. Hmmm.
-
-
-
El filtro EMI está conectado por tres tornillos. Utiliza el destornillador T10 para quitarlos.
-
El tornillo que sujeta tanto el filtro como un cable que está conectado a él es de un tamaño diferente y debe mantenerse identificable de los otros dos tornillos.
-
El cable verde y amarillo que estaba sujeto por el tornillo diferente está metido detrás de otro componente. Para sacarlo, apriétalo detrás del cable negro y el filtro se podrá quitar de la carcasa.
Nothing about the power cable itself here. That has to be unplugged first, or when you get to this point, you’ll have to carefully unplug the main power cable from the back of the AC adapter you just removed in Step 13, and feed it through the hole in the back of the case.
-
Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.
Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.
Cancelar: No complete esta guía.
11 personas más completaron esta guía.
Un agradecimiento especial a estos traductores:
100%
¡ Francisco Javier Saiz Esteban nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
Equipo
Cal Poly, Team 5-11, Maness Spring 2015 Miembro de Cal Poly, Team 5-11, Maness Spring 2015
CPSU-MANESS-S15S5G11
4 Miembros
19 Guías creadas
7 comentarios
Power adapter? That's the AC EMI filter, right? My power supply looks like this:
http://www.dvwarehouse.com/661-6048-661-...
The EMI filter will never fail... well, maybe a direct lightning strike.
That is definitely just a filter. The power supply is the big PCB connected to it. One could say this is an EMI filter along with an IEC input connector...this guide is only useful if you want to replace the connector rather than the actual power supply.
Not sure if the EMI filter will NEVER fail as someone said above. Mine was buzzing and I replaced it and this fixed one of my displays that was buzzing. There are also other causes, including capacitors on the Power Supply board, worn out fan etc.
So are we saying that this is wrong? anyone? I really need to replace my power supply.
I replace the all in one lightning and charge cable but it has ended up that the lightning cable only works. I thought I connected everything up fine but which connector would stop the charge cable working?
Am I imagining things, or was there once a separate power supply guide? I bought the part, and now I can't seem to find that particular guide.. I had the buzzing sound, and now my display won't even turn on-- do I have to replace both, would you think?
Display is going out afther 1 hour of working. I have replace the power supply. But afther installation I still had this problem.
Then I ordered a new Logicboard. and a new cable. Afther installation I still had the same problem !!!. :(
Is it possible that the filter is broken, or the display of the A1407.??
Instead of $14 foam block, I used a full roll of paper towel and two pillows. While it worked, if I ever did this again, I would buy the block of foam. Since you’re removing a power cable, you need to be able thread it through and I think the foam block would make that easier.
Josh Miller - Contestar
You can also use a single handle, double cup floor lifting suction cup. Just place it in the centre of the screen near the camera and lift slowly.
Steve A - Contestar
I just used a toilet plunger to remove the screen and it worked like a charm!
Philip Jacob - Contestar
That’s what I call resourceful—made my day. I hope your repair was successful.
Tobias Isakeit -
Great idea, thanks a lot!
Yvan Sandoz -
The glass lifted off the magnets quite easily after just using my fingernails. No suction cups or toilet accessories needed.
Adrian Gropper - Contestar
I had the same problem and after removal of the fan and a bit of work with the vacuum, the fan is quiet. Thanks to ifixit for the great instructions that made this easy.
John Perser - Contestar
To keep the screen up, other soft objects might work, but it's important that the hole in the back isn't covered because you will need to thread the new Thunderbolt/MagSafe cable through it and it would be a hassle to do it after everything's been set up.
Thomas - Contestar
Anybody got any links to glass screen replacement supplier for the A1407 Thunderbolt Display? Im finding it impossible to find a replacement without it being crazy money.
Michael McMillan - Contestar
Instead of a wedge, I used 4 rolls of toiletpaper, one under each corner.
jnbruin - Contestar