Repara tus cosas Comunidad Tienda

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

Apple Powerbook 5300 Monitor Replacement

Introducción

How to remove and replace the monitor on the Apple Powerbook 5300

Qué necesitas

  1. Apple Powerbook 5300 Monitor Replacement, Battery: paso 1, imagen 1 de 1

    • Position the Powerbook towards you with the monitor closed.

    • Press the battery removal latch located on the right side of the front panel.

    • Gently slide the battery out.

    • The keyboard, front pane, and hard drive are connected to the laptop's logic board via a ribbon cable. Lift up slowly on each component with one hand and disconnect the ribbons from their ports on the logic board.

    Traducir

  2. Apple Powerbook 5300 Monitor Replacement, Keyboard: paso 2, imagen 1 de 1

    • Turn the laptop over and remove the three T8 torx screws from the bottom panel.

    Traducir

  3. Apple Powerbook 5300 Monitor Replacement: paso 3, imagen 1 de 1

    • Turn the laptop back over and open the monitor.

    • With the monitor facing towards you, gently pull up on the keyboard panel from the bottom.

    • With the keyboard turned over as pictured, carefully remove its ribbon cable from the connection port on the logic board. Use a spudger to lift the white plastic retainer about 1/16" to release the cable.

    Traducir

  4. Apple Powerbook 5300 Monitor Replacement, Monitor: paso 4, imagen 1 de 1

    • Remove side panels by pulling up and towards the rear of the laptop. Remove the two torx #8 screws.

    Traducir

  6. Apple Powerbook 5300 Monitor Replacement: paso 5, imagen 1 de 2 Apple Powerbook 5300 Monitor Replacement: paso 5, imagen 2 de 2

    • Disconnect the ribbon cable from the logic board. Note the cable is twisted around the monitor hinge, so do not pull up.

    • Unravel the cable from the hinge first

    Traducir

  7. Apple Powerbook 5300 Monitor Replacement: paso 6, imagen 1 de 2 Apple Powerbook 5300 Monitor Replacement: paso 6, imagen 2 de 2

    • Use a pin to pry up the Powerbook 5300 and Macintosh logos to reveal two torx #8 screws. Remove these screws.

    Traducir

  8. Apple Powerbook 5300 Monitor Replacement: paso 7, imagen 1 de 1

    • Use a wedge tool to pry open the two halves of the monitor assembly. Lift the top half away from the bottom half.

    Traducir

  9. Apple Powerbook 5300 Monitor Replacement: paso 8, imagen 1 de 3 Apple Powerbook 5300 Monitor Replacement: paso 8, imagen 2 de 3 Apple Powerbook 5300 Monitor Replacement: paso 8, imagen 3 de 3

    • Unscrew the three torx #8 screws above and below the white paper backing. Remove the tape and peel back the paper backing to access the screws below.

    Traducir

  10. Apple Powerbook 5300 Monitor Replacement: paso 9, imagen 1 de 3 Apple Powerbook 5300 Monitor Replacement: paso 9, imagen 2 de 3 Apple Powerbook 5300 Monitor Replacement: paso 9, imagen 3 de 3

    • Lift the entire paper and monitor assembly out of its casing. Then, lift the actual monitor out of its paper shell. Be careful not to rip the paper. Watch out for any other wires that might get caught and the speaker cable which is connected to a speaker in the front of the monitor casing.

    Traducir

  11. Apple Powerbook 5300 Monitor Replacement: paso 10, imagen 1 de 1

    • All monitor components should be visible. The transformer board is pictured on the left. The speaker is connected to this board and runs down through the paper housing.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

Autor

con 11 otros colaboradores

Scott

Miembro Desde 04/26/11

155 Reputación

5 Guías creadas

Insignias: 7

+ 4 más insignias

Equipo

Cal Poly, Team 25-30, Garner Spring 2011 Miembro de Cal Poly, Team 25-30, Garner Spring 2011

CPSU-GARNER-S11S25G30

4 Miembros

6 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 7

Ultimos 30 días: 26

Todo El Tiempo: 3,829