Saltar al contenido principal

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

Acer AL1916 Display Replacement

Qué necesitas

  1. Acer AL1916 Display Replacement, Stand: paso 1, imagen 1 de 1
    • Lay the monitor on a flat surface so that the back is facing up.

  2. Acer AL1916 Display Replacement: paso 2, imagen 1 de 2 Acer AL1916 Display Replacement: paso 2, imagen 2 de 2
    • Grab the hinge cover with both hands on either side of the stand.

    • Squeeze inwards with your thumbs and fingers and lift up to remove the hinge cover.

  3. Acer AL1916 Display Replacement: paso 3, imagen 1 de 2 Acer AL1916 Display Replacement: paso 3, imagen 2 de 2
    • Remove the four 12.1 mm Phillips #2 screws that hold the stand to the monitor.

    • Support the monitor while removing the screws to prevent the monitor from falling.

    • Lift up to detach the stand.

  4. Acer AL1916 Display Replacement, Outer Case: paso 4, imagen 1 de 2 Acer AL1916 Display Replacement, Outer Case: paso 4, imagen 2 de 2
    • Remove the five 9.5 mm Phillips #2 screws located around the perimeter of the monitor.

  5. Acer AL1916 Display Replacement: paso 5, imagen 1 de 3 Acer AL1916 Display Replacement: paso 5, imagen 2 de 3 Acer AL1916 Display Replacement: paso 5, imagen 3 de 3
    • Starting at the corner of the monitor, wedge the small plastic opening tool between the back cover and the display bezel.

    • Tilt the plastic opening tool up to separate the back cover from the display bezel.

    • Continue around the perimeter of the monitor until the display bezel comes off.

    • A reasonable amount of force is necessary to detach the back cover from the display bezel.

  6. Acer AL1916 Display Replacement: paso 6, imagen 1 de 2 Acer AL1916 Display Replacement: paso 6, imagen 2 de 2
    • Reposition the monitor so that the back is facing up.

    • Grab the corners of the monitor and jiggle them upwards to detach the back cover from the inside of the monitor.

    • Lift the back cover up.

  7. Acer AL1916 Display Replacement, EMI Shield: paso 7, imagen 1 de 2 Acer AL1916 Display Replacement, EMI Shield: paso 7, imagen 2 de 2
    • Remove the two 5.7 mm Phillips #2 screws located on either side of the EMI shield.

  8. Acer AL1916 Display Replacement: paso 8, imagen 1 de 2 Acer AL1916 Display Replacement: paso 8, imagen 2 de 2
    • Using a nut driver (or if necessary, needle-nose pliers), remove the two nuts on either side of the VGA input.

  9. Acer AL1916 Display Replacement: paso 9, imagen 1 de 3 Acer AL1916 Display Replacement: paso 9, imagen 2 de 3 Acer AL1916 Display Replacement: paso 9, imagen 3 de 3
    • Grab the metal casing by the sides and slide it down towards the bottom of the monitor.

    • Lift up to remove the metal casing.

    • Beware, metal casing is sharp!

  10. Acer AL1916 Display Replacement, Display: paso 10, imagen 1 de 2 Acer AL1916 Display Replacement, Display: paso 10, imagen 2 de 2
    • Remove the three gold 7.5 mm Phillips #2 screws and one silver 8.3 mm Phillips #2 screw from the power supply.

  11. Acer AL1916 Display Replacement: paso 11, imagen 1 de 3 Acer AL1916 Display Replacement: paso 11, imagen 2 de 3 Acer AL1916 Display Replacement: paso 11, imagen 3 de 3
    • Remove the two pieces of yellow tape on the left side of the power supply.

  12. Acer AL1916 Display Replacement: paso 12, imagen 1 de 2 Acer AL1916 Display Replacement: paso 12, imagen 2 de 2
    • Remove the four little white clips located underneath the pieces of tape by lifting up on their left side.

  13. Acer AL1916 Display Replacement: paso 13, imagen 1 de 3 Acer AL1916 Display Replacement: paso 13, imagen 2 de 3 Acer AL1916 Display Replacement: paso 13, imagen 3 de 3
    • With the needle-nose pliers, remove the four display connectors by pulling directly left.

  14. Acer AL1916 Display Replacement: paso 14, imagen 1 de 3 Acer AL1916 Display Replacement: paso 14, imagen 2 de 3 Acer AL1916 Display Replacement: paso 14, imagen 3 de 3
    • Remove the display cable located at the top of the circuit board by pulling it out towards the top of the monitor.

  15. Acer AL1916 Display Replacement: paso 15, imagen 1 de 3 Acer AL1916 Display Replacement: paso 15, imagen 2 de 3 Acer AL1916 Display Replacement: paso 15, imagen 3 de 3
    • Turn the monitor on its side so that the power supply and circuit board are facing to the right

    • Remove the two 6.6 mm Phillips #2 screws located on both sides of the metal casing (four screws total).

  16. Acer AL1916 Display Replacement: paso 16, imagen 1 de 2 Acer AL1916 Display Replacement: paso 16, imagen 2 de 2
    • Set the monitor back down so that the power supply and circuit board are facing you.

    • Feed all four of the connector wires down through the metal casing.

  17. Acer AL1916 Display Replacement: paso 17, imagen 1 de 3 Acer AL1916 Display Replacement: paso 17, imagen 2 de 3 Acer AL1916 Display Replacement: paso 17, imagen 3 de 3
    • Grab the sides of the metal casing and lift up.

    • Turn the display over to see the front; you are ready replace the broken display with a new one!

Conclusión

To reassemble your device, follow these instructions in reverse order.

5 personas más completaron esta guía.

Keith

Miembro Desde 10/06/11

336 Reputación

4 Guías creadas

Equipo

Cal Poly, Team 20-26, Maness Fall 2011 Miembro de Cal Poly, Team 20-26, Maness Fall 2011

CPSU-MANESS-F11S20G26

4 Miembros

14 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 8

Ultimos 30 días: 31

Todo El Tiempo: 8,760