Saltar al contenido principal

Introducción

This guide will demonstrate how to replace the back camera of a Zenfone 3. This may be necessary if the camera no longer shows a picture or shows a distorted picture. For this guide, you will need the tweezers, Torx T2 screwdriver, a prying tool, and the Phillips #00 screwdriver.

  1. Using a pair of tweezers, pull put the SIM card tray and set it to the side. Using a pair of tweezers, pull put the SIM card tray and set it to the side.
    • Using a pair of tweezers, pull put the SIM card tray and set it to the side.

  2. Remove the two 2 mm screws using a Torx T2 screwdriver.
    • Remove the two 2 mm screws using a Torx T2 screwdriver.

  3. Insert a prying tool between the screen and the metal backing of the phone at the bottom to remove backing from phone. There will be a thin film connecting the two pieces. You do not need to remove this. Just fold the two pieces apart with the inside facing up.
    • Insert a prying tool between the screen and the metal backing of the phone at the bottom to remove backing from phone.

    • There will be a thin film connecting the two pieces. You do not need to remove this. Just fold the two pieces apart with the inside facing up.

  4. Remove the two 3 mm screws, using the Phillips #00 screwdriver, on the silver band at the top of the battery and remove the band.
    • Remove the two 3 mm screws, using the Phillips #00 screwdriver, on the silver band at the top of the battery and remove the band.

  5. Peel back the silver tape.
    • Peel back the silver tape.

  6. Kits de Reparación de Batería de iPhone

    Sólo $29.99

    Buy Now

    Kits de Reparación de Batería de iPhone

    Sólo $29.99

    Buy Now
  7. Disconnect the battery connections.
    • Disconnect the battery connections.

  8. Pry and remove the battery.
    • Pry and remove the battery.

    • The underside of the battery is adhesive so make sure to pry the battery off gently.

  9. Remove the 3 mm screws, using the Phillips #00 screwdriver, from the black plastic piece at the top on the right side. Remove the 3 mm screws, using the Phillips #00 screwdriver, from the black plastic piece at the top on the right side. Remove the 3 mm screws, using the Phillips #00 screwdriver, from the black plastic piece at the top on the right side.
    • Remove the 3 mm screws, using the Phillips #00 screwdriver, from the black plastic piece at the top on the right side.

  10. Remove the 3 mm screws, using the Phillips #00 screwdriver, from the metal piece around the camera.
    • Remove the 3 mm screws, using the Phillips #00 screwdriver, from the metal piece around the camera.

  11. Remove the 3 mm circuit board screws, using the Phillips #00 screwdriver. Remove the 3 mm circuit board screws, using the Phillips #00 screwdriver.
    • Remove the 3 mm circuit board screws, using the Phillips #00 screwdriver.

  12. Unplug the two wires at the bottom of the circuit board. Unplug the two wires at the bottom of the circuit board. Unplug the two wires at the bottom of the circuit board.
    • Unplug the two wires at the bottom of the circuit board.

  13. Remove the circuit board.
    • Remove the circuit board.

  14. Unplug the camera. Unplug the camera.
    • Unplug the camera.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 7

Últimos 30 Días: 41

Todo El Tiempo: 288