Saltar al contenido principal

Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.

Qué necesitas

  1. Este paso está sin traducir. Ayuda a traducirlo

    : paso 1, imagen 1 de 2 : paso 1, imagen 2 de 2
    • Locate the hood latch beside the driver's side door, next to the left foot rest.

    • Pull the latch toward you to release the hood.

  2. Este paso está sin traducir. Ayuda a traducirlo

    : paso 2, imagen 1 de 2 : paso 2, imagen 2 de 2
    • Walk around to the front of the vehicle.

    • Slide your hand under the hood, directly above the Honda emblem. Locate and pull the hood tab to unlock the hood.

    • Once the tab is released, lift the hood up.

  3. Este paso está sin traducir. Ayuda a traducirlo

    : paso 3, imagen 1 de 2 : paso 3, imagen 2 de 2
    • Use your left hand to hold the hood up. Locate the hood stand and pull it out of the clip.

    • Place the tip of the hood stand into the hole located in the upper left of the hood.

    • You can now let the hood rest on the stand.

  4. Este paso está sin traducir. Ayuda a traducirlo

    : paso 4, imagen 1 de 3 : paso 4, imagen 2 de 3 : paso 4, imagen 3 de 3
    • Be sure your engine is turned off.

    • Identify the engine's air duct hose.

    • The emission hose is located on the top.

    • Remove the emission hose by gently wiggling it out of place.

  5. Este paso está sin traducir. Ayuda a traducirlo

    : paso 5, imagen 1 de 2 : paso 5, imagen 2 de 2
    • Remove the smog hose by squeezing the tubing and pulling it off.

  6. Este paso está sin traducir. Ayuda a traducirlo

    : paso 6, imagen 1 de 1
    • Using a Phillips screwdriver, loosen air duct clamp screws.

  7. Este paso está sin traducir. Ayuda a traducirlo

    : paso 7, imagen 1 de 2 : paso 7, imagen 2 de 2
    • Once the screws are loose, completely remove the air duct hose by gently wiggling it off the engine and the air filter housing.

  8. Este paso está sin traducir. Ayuda a traducirlo

    : paso 8, imagen 1 de 3 : paso 8, imagen 2 de 3 : paso 8, imagen 3 de 3
    • Remove the air filter housing cap.

    • Using a long Phillips screwdriver or a long 5/16 Hex driver, remove the four screws holding down the air filter housing cap.

  9. Este paso está sin traducir. Ayuda a traducirlo

    : paso 9, imagen 1 de 1
    • Lift the engine air filter housing cap and place it aside.

    • Do not turn the housing cap upside down. Screws left in holes of housing cap might fall out.

  10. Este paso está sin traducir. Ayuda a traducirlo

    : paso 10, imagen 1 de 1
    • Lift the dirty filter out of the housing.

    • Vacuum any dirt or debris out of the air filter box.

  11. Este paso está sin traducir. Ayuda a traducirlo

    : paso 11, imagen 1 de 1
    • Replace the old filter with the new filter.

    • Ensure that it seats properly in the lip of the air cleaner box.

    • Screw down the air filter housing cap. Connect air dust, emission, and smog hoses.

Linea de Meta

21 personas más completaron esta guía.

Shaun MacDonald

Miembro Desde 10/03/12

2,528 Reputación

8 Guías creadas

Equipo

Cal Poly, Team 24-27, Regan Fall 2012 Miembro de Cal Poly, Team 24-27, Regan Fall 2012

CPSU-REGAN-F12S24G27

4 Miembros

21 Guías creadas

4 comentarios

Okay, I have an Acura TSX (Euro Accord) with the K24A engine, which is similar, and can assure you that you do not need to remove all these connections and hoses just to open the engine air cleaner . The AIR CLEANER COVER (where the filter lives) can be gently lifted up sufficiently to open up, remove the AIR CLEANER ELEMENT ASSY (filter), vacuum out debris from AIR CLEANER CASE, and install a new filter.

David Spalding - Contestar

For a 2006 Accord L4, you definitely need to remove the air intake hose as the front lip of the air cleaner box will not clear the inner fender by about 1/4" on the left side. Never had problems with any other newer or older hondas and toyotas with having to remove the air intake hose to open the air cleaner box. This is why I came here for advice. thanks OP.

Michael Lee - Contestar

emission hose where can I find it at ? Mine broke

Moda Zuniga - Contestar

You use metric tools on Hondas because they are a foreign car. Use an 8mm socket with an extension to remove the screws from the air filter cover.

Mary Petersonma - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 26

Ultimos 30 días: 138

Todo El Tiempo: 33,159