Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Partes y herramientas

  1. Use a #2 Phillips screwdriver to remove the four screws.
    • Use a #2 Phillips screwdriver to remove the four screws.

  2. Remove the rubber gasket from the rain tray.
    • Remove the rubber gasket from the rain tray.

  3. Lift the tray upwards and away from the vehicle.
    • Lift the tray upwards and away from the vehicle.

  4. Use a flathead screwdriver to remove the cap from the windshield wiper.
    • Use a flathead screwdriver to remove the cap from the windshield wiper.

  5. Kits para Nintendo Switch

    Una solución rápida para volver al juego

    Comprar kits de Switch

    Kits para Nintendo Switch

    Una solución rápida para volver al juego

    Comprar kits de Switch
  6. Use a socket wrench to release the passenger-side windshield wiper locking nut.
    • Use a socket wrench to release the passenger-side windshield wiper locking nut.

  7. Gently lift up the passenger-side windshield wiper. Gently lift up the passenger-side windshield wiper.
    • Gently lift up the passenger-side windshield wiper.

  8. Remove the driver-side windshield wiper in the same fashion.
    • Remove the driver-side windshield wiper in the same fashion.

    My windshield wipers were stuck on like they were welded. I removed them with channel lock pliers. I put the top jaw of the pliers and placed it under the wiper and the bottom claw of the pliers and put it on the mounting bolt. squeezed as hard as I could and Pop! It came loose.

    Nils Stansen - Contestar

  9. Lift up the plastic cover. Lift up the plastic cover.
    • Lift up the plastic cover.

    There is a lip on the back side of the cowling. I placed a flat pry bar underneath the cowling from the engine compartment towards the windshield and used the flat lip of the firewall top edge to pry the cowling straight up; not forward or backward but straight up. Mine was stuck with years of debris that turned to a natural glue!

    Nils Stansen - Contestar

  10. Use an offset Phillips screwdriver to remove a screw in the back of the automatic control unit cover. In a pinch, you can make this tool with a phillips driver bit and end wrench.
    • Use an offset Phillips screwdriver to remove a screw in the back of the automatic control unit cover.

    • In a pinch, you can make this tool with a phillips driver bit and end wrench.

  11. Use a #2 Phillips screwdriver to remove the front two screws.
    • Use a #2 Phillips screwdriver to remove the front two screws.

  12. Gently unplug and lift out the automatic transmission control unit. Gently unplug and lift out the automatic transmission control unit.
    • Gently unplug and lift out the automatic transmission control unit.

Conclusión

To reassemble your device, follow these instructions in reverse order.

7 personas más completaron esta guía.

Matthew Newsom

Miembro Desde 05/01/10

34,875 Reputación

67 Guías creadas

Does the new TCU need to be programmed in any way?? Or is it just plug and play.

Paul Newlove - Contestar

does it need to be programmed mine needs replacement my gears are not shifting

dean wafula - Contestar

got a question if your display light is dim what could be the problem

dean wafula - Contestar

Volkswagen tiguan won't start after disconnection, wat can I do to restart it

Jusu Suapay - Contestar

thank you very much .

emad_szs - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 6

Ultimos 7 días: 30

Ultimos 30 días: 188

Todo El Tiempo: 35,424