Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Tienda

Herramientas Destacadas en este Teardown

Este desmontaje no es una guía de reparación. Para reparar tu iPod Nano 1st Generation, utiliza nuestros manuales de servicio .

  1. Este paso está sin traducir. Ayuda a traducirlo

    1.    Using an ipod unclipping tool (which could be a knife or similar to it), unclip the outer casing by putting the tool up to the connection point. This should pop the case off. Note that force will need to be used. 1.    Using an ipod unclipping tool (which could be a knife or similar to it), unclip the outer casing by putting the tool up to the connection point. This should pop the case off. Note that force will need to be used.
    • 1. Using an ipod unclipping tool (which could be a knife or similar to it), unclip the outer casing by putting the tool up to the connection point. This should pop the case off. Note that force will need to be used.

  2. Este paso está sin traducir. Ayuda a traducirlo

    2.    Remove the circuit board by unscrewing the 3 screws (there is 1 more screw but dont unscrew it, it holds the headphone jack) that hold it down. Note that specialised screwdrivers may need to be used.
    • 2. Remove the circuit board by unscrewing the 3 screws (there is 1 more screw but dont unscrew it, it holds the headphone jack) that hold it down. Note that specialised screwdrivers may need to be used.

  3. El kit de herramientas esencial

    Las herramientas más útiles en nuestro kit más compacto.

    Compra ahora

    El kit de herramientas esencial

    Las herramientas más útiles en nuestro kit más compacto.

    Compra ahora
  4. Este paso está sin traducir. Ayuda a traducirlo

    3. Carefully remove the connected wires underneath the motherboard to disconnect the clickwheel and the screen. 3. Carefully remove the connected wires underneath the motherboard to disconnect the clickwheel and the screen.
    • 3. Carefully remove the connected wires underneath the motherboard to disconnect the clickwheel and the screen.

  5. Este paso está sin traducir. Ayuda a traducirlo

    4.    The screen has 3 different sections, each held down by glue so necessary force is needed. First remove the acrylic backing that supports the screen and then the main part of the screen. The last thing to remove is the paper-thin cover. 4.    The screen has 3 different sections, each held down by glue so necessary force is needed. First remove the acrylic backing that supports the screen and then the main part of the screen. The last thing to remove is the paper-thin cover. 4.    The screen has 3 different sections, each held down by glue so necessary force is needed. First remove the acrylic backing that supports the screen and then the main part of the screen. The last thing to remove is the paper-thin cover.
    • 4. The screen has 3 different sections, each held down by glue so necessary force is needed. First remove the acrylic backing that supports the screen and then the main part of the screen. The last thing to remove is the paper-thin cover.

  6. Este paso está sin traducir. Ayuda a traducirlo

    5.    Removing the touchpad is easy and simple as there are layered parts on top of each other, just simply and carefully pull them off. 5.    Removing the touchpad is easy and simple as there are layered parts on top of each other, just simply and carefully pull them off. 5.    Removing the touchpad is easy and simple as there are layered parts on top of each other, just simply and carefully pull them off.
    • 5. Removing the touchpad is easy and simple as there are layered parts on top of each other, just simply and carefully pull them off.

  7. Este paso está sin traducir. Ayuda a traducirlo

    6.    Finally you should have the ipod dismantelled and you should be able to put the ipod back together.
    • 6. Finally you should have the ipod dismantelled and you should be able to put the ipod back together.

Craig Lawrence

Miembro Desde 11/03/10

444 Reputación

1 Guía escrita

when i put the rear cover back on, the charging station doesn't line up correctly and the charging station sticks out a bit. any advice?

krnchang - Contestar

is the batter swollen

Derek King - Contestar

Yes, happened to a Zune 80 I have

Crazyblocks Technologies -

Thank you for this - took the fear factor out of changing battery on my much loved Nano!

jimbradshaw - Contestar

It’s extremely hard to connect LCD and Button cables. I screwed it up while reconnecting the cables. IF, you want to disassemble this machine by fun, don’t ever try it.

Sizun Cho - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 5

Ultimos 7 días: 32

Ultimos 30 días: 136

Todo El Tiempo: 23,356