Introducción

We are going to start with the base of the fan, and move to the top afterwords.

Este desmontaje no es una guía de reparación. Para reparar tu GD Midea FT30-3D, utiliza nuestros manuales de servicio .

  1. Locate and remove the 14.5 mm Phillips #1 screw on the bottom of the fan base.
    • Locate and remove the 14.5 mm Phillips #1 screw on the bottom of the fan base.

    Agregar Comentario

  2. Locate the gray base support release tabs found on either side pictured in the first image.
    • Locate the gray base support release tabs found on either side pictured in the first image.

      • There are release tabs on each side of the base.

    • Press both release tabs in with the tip of your fingers and pull the gray base support until the tabs are cleared.

    Agregar Comentario

    • Continue removing the gray base support by pressing your thumb into the circular opening in the base and pulling with your figures on the back side.

    • Notice that on the internal front tip of the base there is a tab. Because of this tab the back end will pivot off at that point.

    Agregar Comentario

    • After the base has separated more it will be easy to fully remove it. Continue pulling the back edge of the gray base support, rotating it around the front tab until it comes off completely.

    Agregar Comentario

    • Remove the following five 14.5 mm Phillips #1 screws found on the bottom.

      • All of the screws are recessed by 17.5 mm, so ensure your screwdriver can reach that far.

    Agregar Comentario

    • Once all five screws have been removed the base cover should fall right off with out any effort.

    • When putting the base cover back on; be careful to make sure that none of the wires are pinched.

    Agregar Comentario

    • Remove the two 15 mm Phillips screws on the retention plate.

    • The tan retention plate will fall off once the screws are removed.

    Agregar Comentario

    • Take the 1.5 mm Flathead Screwdriver, or any thin elongated tool that fits into the semi-circular holes along side the AC power cord white wire. Press into the hole gently to release the grip on the wire.

    • The AC power cord wire should release with ease if done properly.

    Agregar Comentario

    • Cut the existing cable tie bundling the other AC power cord, red, orange, gray, and blue wires together.

    • Remove or cut the crimp connector connecting the blue wire and the AC power cord wire.

    Agregar Comentario

  3. Reparte el espíritu de reparación esta Navidad
    Obtén $12 de descuento en tu compra de $50 o más con el código FIXMAS12
    Reparte el espíritu de reparación esta Navidad
    Obtén $12 de descuento en tu compra de $50 o más con el código FIXMAS12
    • Remove the two 10 mm Phillips #1 screws found connecting the switch to the case.

    • Notice the AC power cord line (white wire) goes into the switch under the [Off] button

    Agregar Comentario

    • Take the 1.5 mm Flathead Screwdriver, or any thin elongated tool that fits into the semi-circular holes along side the wires. Press into the hole gently to release the grip on the wires.

      • The wires should release with ease if done properly.

    • When reassembling; skip this step.

    Agregar Comentario

    • Take the new switch, and simply push the wiring into the correct holes:

      • AC Power Cord (white wire)

      • Low speed (gray wire)

      • Medium speed (orange wire)

      • High speed (red wire)

    Agregar Comentario

    • Release the 3 clips that attach the front fan guard to the rear fan guard.

    • Notice: The lower connecting bracket is NOT a clip. It acts as a mounting alignment bracket for the front fan guard.

    Agregar Comentario

    • Pull the front fan guard off.

    Agregar Comentario

    • Remove the spinner from the center of the fan blade.

    Agregar Comentario

    • The fan blades should now be easy to lift up.

    • When reassembling the fan make sure the notches in the center of the fan blade line up with the protrusions in the motor's shaft.

    Agregar Comentario

    • At the base of the upper assembly there is a plug which conceals a screw.

    • The plug can be removed with a screwdriver. Removing the plug may take a few attempts.

    Agregar Comentario

    • Slide the motor out of the base of the upper assembly.

    Agregar Comentario

    • Remove the rear fan guard by taking off the plastic nut that holds the rear fan guard to the upper assembly.

    • The plastic nut needs to be twisted off; like a screw.

    Agregar Comentario

    • Remove the screw at the center of the oscillator knob and remove the oscillator knob.

    • If the oscillator knob is clean and undamaged then the problem is with the oscillator. If the knob is damaged replace it and test your fan before proceeding forward in the guide.

    Agregar Comentario

    • Remove the front motor housing by removing 4 screws.

    Agregar Comentario

    • The main motor housing can be taken off by removing a single screw at the back of the upper assembly.

    Agregar Comentario

    • There is a capacitor attached to the oscillator by a single screw. Once the screw is removed the capacitor should come off easily.

    the two wires of capacitors are connected where ?? please guide me.

    mohangmysore - Contestar

    The two wires are normally connected to the motors, start winding.

    zakk - Contestar

    • Remove the screw that connects the oscillator to the rocker arm.

    • Push down on the rocker arm after removing the screw and turn it away from the oscillator.

    Agregar Comentario

    • The oscillator should now be easy to pull off.

    • Clean the oscillator and remove any jams. If the problem persists the oscillator is damaged and needs to be replaced.

    Agregar Comentario

Jonathan Leposky

Miembro Desde 04/10/12

64 Reputación

1 Guía escrita

Equipo

Cal Poly, Team 24-28, Regan Fall 2012 Miembro de Cal Poly, Team 24-28, Regan Fall 2012

CPSU-REGAN-F12S24G28

4 Miembros

10 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 4

Todo El Tiempo: 3,429