Herramientas Destacadas en este Teardown

Este desmontaje no es una guía de reparación. Para reparar tu Sega CD, utiliza nuestros manuales de servicio .

Using a Phillips head screwdriver remove  six screws from the bottom of the console.
  • Using a Phillips head screwdriver remove six screws from the bottom of the console.

    • The six screws are marked.

Agregar Comentario

Remove the two screws that attach the Genesis' connector to the rest of the console.
  • Remove the two screws that attach the Genesis' connector to the rest of the console.

    • The two screws are marked in the diagram.

Agregar Comentario

  • Slide the lock tab to the left to separate the halves of the console.

Agregar Comentario

  • Lift from the left side to remove the top of the case.

Agregar Comentario

  • Using the spudger, pry the cover off of the Genesis attachment.

Agregar Comentario

  • Lift the top of the case to remove the cover.

Agregar Comentario

  • Remove the faceplate by pulling it up, then out.

Agregar Comentario

  • Using a #00 Philips screwdriver remove the two screws that attach the Genesis adapter to the console.

  • Disconnect the adapter from the console by carefully pulling the adapter out.

Agregar Comentario

  • Remove the four screws from the metal plate as shown using a #00 Philips screwdriver.

    • The four half inch bronze screws are indicated by the yellow marking circles.

Agregar Comentario

  • Carefully remove the metal cover from the connector by sliding the cover up and out.

Agregar Comentario

  • Remove the connector from the housing.

Agregar Comentario

  • Remove metal plate by unscrewing the three screws with the Phillips head screwdriver and then lifting the plate.

    • The three screws are shown on the diagram.

Agregar Comentario

  • Remove the two screws from the plastic bar.

    • The two screws are shown pictured.

Agregar Comentario

  • To remove the CD tray

    • Remove the four screws with the Phillips head screwdriver.

Agregar Comentario

  • Carefully unplug the wire connected to optical reader.

Agregar Comentario

  • Remove the four screws on the underside of the CD tray with a small Phillips head screwdriver.

    • The four screws are highlighted on the diagram.

  • The four springs below the circuit board are attached to the screws, so be careful not to lose them when you remove the screws.

Agregar Comentario

  • Carefully remove the CD tray from circuit board.

Agregar Comentario

  • Remove the two bronze screws from the metal plate with a medium Phillips head screwdriver.

    • The screws are marked on the diagram.

  • Carefully lift the metal plate up to expose the motherboard.

    • There is a wire strip running through the metal plate that is soldered to motherboard and power supply board. The plate cannot be completely removed. Do NOT force plate upwards. All the ribbon cables can be safely unplugged by simply pulling them out of their slots.

The yellow circles in this diagram are incorrect. There are 3 screws on the main board assembly. 2 on the left and one correctly indicated on the bottom right. The top right yellow circle does not belong.

myersni06 - Contestar

  • Carefully lift off the metal plate, the motherboard, and the CD tray circuit board. Then, flip each piece over, as pictured.

Agregar Comentario

  • Remove the two screws from the power supply using a medium Phillips head screwdriver.

    • The two screws are marked on the diagram.

Agregar Comentario

  • Remove the power supply unit from the console by lifting the unit up.

Agregar Comentario

  • This is what the motherboard unit will look like once removed.

Agregar Comentario

  • Teardown complete!

Ryan Kotzebue

Miembro Desde 07/10/10

243 Reputación

4 Guías creadas

Equipo

Cal Poly, Team 5-14, Maness Fall 2010 Miembro de Cal Poly, Team 5-14, Maness Fall 2010

CPSU-MANESS-F10S5G14

5 Miembros

6 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 8

Últimos 7 Días: 31

Últimos 30 Días: 85

Todo El Tiempo: 11,061